subject

Chemistry, 07.12.2019 03:31 2965276513

Calcium reacts with oxygen to form calcium oxide. the chemical equation for this reaction is ca + o2→cao . what is the product, or what are the products, of this reaction? a. caob. o 2c. ca + o2d. ca

ansver

Answers: 3

Show answers

Another question on Chemistry

question

Chemistry, 22.06.2019 06:30

What is the polyatamic ion of borate

Answers: 1

question

Chemistry, 22.06.2019 10:30

Balance and in which category does it fit in? single or double displacement or synthesis or decomposition? (a) k2 o → k + o2 (b) na + i2 → nai (c) cu(no3 )2 + naoh → cu(oh)2 + nano3 (d) kclo3 → kcl + o2 (e) ca(no3 )2 + hbr → cabr2 + hno3 (f) sn(oh)2 → sno + h2 o (g) p4 + n2 o → p4 o6 + n2 (h) fe + al2 (so4 )3 → feso4 + al (i) alcl3 + na2 co3 → al2 (co3 )3 + nacl (j) c3 h6 + o2 → co2 + h2 o

Answers: 1

question

Chemistry, 22.06.2019 22:00

Scientists often have to deal with numbers that are either very large or very small. for example, the radius of the sun is approximately 696,000 kilometers, while bacterial cells are as small as 1.9 × 10-4 millimeters. express each number in an alternate form.

Answers: 1

question

Chemistry, 23.06.2019 00:20

4. propanol and isopropanol are isomers. this means that they have a) the same molecular formula but different chemical properties. b) different molecular formulas but the same chemical properties. c) the same molecular formula and the same chemical properties. d) the same molecular formula but represent different states of the compound

Answers: 3

You know the right answer?

Calcium reacts with oxygen to form calcium oxide. the chemical equation for this reaction is ca + o2...

Questions

question

Engineering, 13.09.2019 23:20

Two factors that can be modified to optimize the cutting processes are feed and depth, and cutting velocity. a) true b) false...

question

Engineering, 13.09.2019 23:20

The highest cutting temperature is located close to the shear zone. a) true b) false...

question

Engineering, 13.09.2019 23:20

The largest source of heat generated in metal cutting is due to friction. a) true b) false...

question

Engineering, 13.09.2019 23:20

Calculate the differential pressure in kpa across the hatch of a submarine 320m below the surface of the sea. assume the atmospheric pressure at the s...

question

Engineering, 13.09.2019 23:20

Increasing rake angle will decrease the tendency for built-up-edge to form. a) true b) false...

question

Engineering, 13.09.2019 23:20

An orthogonal cutting operation is performed using a rake angle of 15°, to=0.012 in and w=0.100 in. the chip thickness ratio is measured after the cut...

question

Engineering, 13.09.2019 23:20

Write the type of chips generated at each of the following cutting conditions, and explain why. a. low cutting speed: b. large depth of cut: c. very...

question

Engineering, 13.09.2019 23:20

How are the polymeric materials classified? give examples of the plastic materials and elastomers? give the difference between thermoplastics and t...

question

Engineering, 13.09.2019 23:20

What is components? what is phases? what is tie line?...

question

Engineering, 13.09.2019 23:20

Avariable speed reciprocating compressor of mass 400 kg has a natural frequency of 16.2 hz. (a) design an optimum auxiliary mass damper, so that the m...

question

Engineering, 13.09.2019 23:20

Specific cutting energy increases with increasing the cutting speed. a) true b) false...

question

Engineering, 13.09.2019 23:20

Two standard spur gears have a diametrical pitch of 10, a center distance 3.5 inches and a velocity ratio of 2.5. how many teeth are on each gear?...

question

Engineering, 13.09.2019 23:20

Consider a wind turbine subjected to 30 km/hr steady winds. if the turbine produces 480 kw of power and the velocity downstream of the wind turbine is...

question

Engineering, 13.09.2019 23:20

You are traveling in an airplane. the engineer who designed it is, casually, on your side. he tells you that the wings were designed using the von mis...

question

Engineering, 13.09.2019 23:20

Cost of machining operations is primarily affected by tool life, power consumed and workpiece material. a) true b) false...

question

Engineering, 13.09.2019 23:20

What is the difference between "independent variables" and "dependent variables" in metal cutting operations? give three examples of each....

question

Engineering, 13.09.2019 23:20

Determine the molar air-fuel ratio for hydrogen (h2) burning with (a) 50% excess air and (b) 50% deficient air....

question

Engineering, 13.09.2019 23:20

Steam enters the high pressure turbine of a reheat cycle power plant at 3.5 mpa and 350and expands to 0.5 mpa after which it is reheated to 350°c. the...

question

Engineering, 13.09.2019 23:20

Aloan for $85,000 is to be paid in 10 yearly payments. each payment is larger by $100.00. compute the first, the fourth, and the last payment, if the...

question

Engineering, 13.09.2019 23:20

Asolid shaft and a hollow shaft of the same material have same length and outer radius r. the inner radius of the hollow shaft is 0.7r. a) if both the...

More questions: Chemistry Another questions

Questions on the website: 13722363