Chemistry, 27.08.2020 07:01 gordwindisney3747

If your experimentally measured volume of the bolt was too small, would that make the density value larger or smaller?

Answers: 1

Show answers

Answers

Answer from: Quest

D-no effect on the rate

Answer from: Quest

honesty and integrity.

inspire others.

commitment and passion.

good communicator.

decision-making capabilities.

accountability.

delegation and empowerment.

creativity and innovation.

here are the traits of a good leader.i'm not going to give you the examples so you can copy right it.that's illegal but i hope that this you out.

Answer from: Quest

Note that 2 mol dm⁻³ = 2 mol/(dm³)outline: we're given the concentration of hcl, which is 2 mol dm⁻³ (cubic meters in the denominator can represent volume, so i know this is concentration). we're an amount of calcium carbonate caco₃, which is 5 g. we're presented with a chemical equation which includes caco₃ and hcl. we are told to find the volume of hcl. from what we see so far, this seems to be a stoichiometry problem. we'll have to use the given information about calcium carbonate to find the amount of moles of hcl needed to fully react with calcium carbonate. then we'll have information about the moles of hcl and the concentration of hcl; that will be enough to figure out volume according to the formula concentration = moles / volume.======all the answer choices are not in dm.convert the given concentration so that it uses cm⁻³.we can use conversion factors. we have to cube our conversion factors so that dimensional analysis works.we can convert to meters first, using the fact that 10 dm = 1 m ⇔ 10³ dm³ = 1 m³then we use the fact that 10² cm = 1 m ⇔ (10² cm)³ = (1 m)³ ⇔ 10⁶ cm³ = 1 m³so converting: $\dfrac{\text{2 mol}}{\text{dm}^{3}} \cdot \dfrac{\text{10}^3\text{ dm}^3}{\text{1 m}^3} \cdot \dfrac{\text{1 m}^3}{10^6\text{ cm}^3} \\ \\ = \dfrac{\text{2 mol}}{1} \cdot \dfrac{\text{10}^3}{1} \cdot \dfrac{1}{10^6\text{ cm}^3} \qquad \text{\footnotesize cancelling units} \\ \\ = \dfrac{2\text{ mol}}{10^3 \text{ cm}^3} \\ \\ = 0.002\text{ mol/cm}^3$ now we have to find the moles of hydrochloric acid neededfind the moles of calcium carbonate. we have to find the molar mass of calcium carbonate, caco₃, which can be found by molar mass = (mass ca) + (mass c) + 3(mass o) = 40 + 12 + 3(16) = 100 g/molconvert the given 5 g to moles: mol caco₃ = 5 g caco₃ * 1 mol/(100 g) = 0.05 mol caco₃use stoichiometry (ratios) to figure out the moles of hcl needed. ratio wise, there's 2 hcls for every caco₃, so use dimensional analysis mol hcl = mol caco₃ * (2 mol hcl) / (1 mol caco₃) = 0.05 mol hcl * 2 = 0.1 mol hcl we have 0.1 mol hcl and concentration of hcl (0.002 mol/cm³).we need to find volumesince concentration = moles / volume, rearrange to get volume = moles / concentration volume = 0.1 mol / (0.002 mol/cm³) volume = 50 cm³

Answer from: Quest

its b it was a compound

Another question on Chemistry

Chemistry, 22.06.2019 06:30

The following reaction shows the products when sulfuric acid and aluminum hydroxide react. al(oh)3 + h2so4 → al2(so4)3 + h2o the table shows the calculated amounts of reactants and products when the reaction was conducted in a laboratory. sulfuric acid aluminum hydroxide initial amount of reactant 40 g 15 g theoretical yield of water from reactant 14.69 g 10.38 g what is the approximate amount of the leftover reactant? 11.73 g of sulfuric acid 10.33 g of sulfuric acid 11.12 g of aluminum hydroxide 13.67 g of aluminum hydroxide

Answers: 3

Answer

Chemistry, 22.06.2019 13:00

In a copper wire, a temperature increase is the result of which of the following

Answers: 1

Answer

Chemistry, 22.06.2019 18:00

Answer asap need to be answered by wednesday morning explain how a buffer works, using an ethanoic acid / sodium ethanoate system including how the system resists changes in ph upon addition of a small amount of base and upon addition of a small amount of acid respectively. include the following calculations in your i. calculate the ph of a solution made by mixing 25cm3 0.1m ch3cooh and 40cm3 0.1m ch3coo-na+. [ka = 1.74 x 10-5 m] ii. calculate the ph following the addition of a 10cm3 portion of 0.08 m naoh to 500cm3 of this buffer solution. iii. calculate the ph following the addition of a 10cm3 portion of 0.08 m hcl to 200cm3 of the original buffer solution.

Answers: 3

Answer

Chemistry, 22.06.2019 18:10

The atom fluorine generally will become stable through the formation of an ionic chemical compound by accepting electron(s) from another atom. this process will fill its outer energy level of electrons.

Answers: 1

Answer

You know the right answer?

If your experimentally measured volume of the bolt was too small, would that make the density value...

Questions