subject

Chemistry, 08.12.2020 14:00 jackolantern1437

Which statement explains why the compass needle points in the direction it
does?

ansver

Answers: 2

Show answers

Another question on Chemistry

question

Chemistry, 22.06.2019 14:00

What was bohr’s contribution to the planetary model

Answers: 1

question

Chemistry, 23.06.2019 01:30

Which statement justifies that hydrogen peroxide (h2o2) is a polar molecule? the o – h bond is nonpolar and the molecule is asymmetric. the o – h bond is nonpolar and the molecule is symmetric. the o – h bond is polar and the molecule is asymmetric. the o – h bond is polar and the molecule is symmetric.

Answers: 1

question

Chemistry, 23.06.2019 08:00

Which of the following notations would be the appropriate and final way to display the formula for magnesium chloride a. mgcl2 b. mg+2cl–1 c. mgcl2 d. mgcl

Answers: 2

question

Chemistry, 24.06.2019 00:00

The nonmetals in groups 6a and 7a a) end in -ate b) have a numerical charge that is found by subtracting 8 from the group number c) all have ions with a –1 charge d) lose electrons when they form ions

Answers: 3

You know the right answer?

Which statement explains why the compass needle points in the direction it
does?...

Questions

question

Social Studies, 26.07.2019 17:20

Agang member threatened to kill the defendant unless he robbed a convenience store and gave the proceeds to the gang member. the gang member also dema...

question

Business, 26.07.2019 17:20

Other things held constant, which of the following would tend to reduce the cash conversion cycle? offer longer payment terms to customers. continue...

question

Biology, 26.07.2019 17:20

Terrance, whose birth mother drank heavily throughout pregnancy, has a thin upper lip, short eyelid openings, a small head, and a smooth philtrum. his...

question

Physics, 26.07.2019 17:20

"for a first order instrument with a sensitivity of .4 mv/k and a time" constant of 25 ms, find the instrument’s response as a function of time for a...

question

Mathematics, 26.07.2019 17:20

You and your friend are at a shooting range. you ran out of bullets. your friend still has two bullets left but magically lost his gun. somehow you bo...

question

Engineering, 26.07.2019 17:20

Initially there are 3 [kg) of gas at a pressure of 200 [kpa] and specific volume of 1.5 [m3/kgl contained within a piston cylinder assembly. the gas u...

question

Engineering, 26.07.2019 17:20

In machining, if the cost to purchase/regrind the cutting tool=$0.00, the optimum speed for machining time minimization would be different from the op...

question

Engineering, 26.07.2019 17:20

In turning, if the spindle speed (spindle rpm) increases by a factor of four, while the feed rate decreases by a factor of four, will the ideal surfac...

question

Engineering, 26.07.2019 17:20

Oil, with a density of ρ = 900 kg m=3 and a kinematic viscosity of v = 0.1 m^2 s^-1, flows at a volume flow rate of q 0.2 m^3 s^-1 through 500 m of 20...

question

Engineering, 26.07.2019 17:20

What is an involute profile and why is it used in gear tooth design?...

question

Engineering, 26.07.2019 17:20

If i can live with a 3% probability of failure, select a ball bearing design (independent of shaft diameter that will carry a 120 ib load at 3000 rpm....

question

Engineering, 26.07.2019 17:20

Determine the diameter of a cylindrical capillary tube needed to observe a 0.4" rise for water if the contact angle is 12°...

question

Engineering, 26.07.2019 17:20

If a cutting operation is performed at a feed rate of 5 in/min, and the feed is 0,005 in/rev, then the spindle rpm is: i. 5000 rpm. i. 1000 rpm. ili....

question

Engineering, 26.07.2019 17:20

Describe the general steps in the journal bearing design procedure. outline approach with substeps identified is fine....

question

Engineering, 26.07.2019 17:20

How are the pressure angle, pitch circle and base circle for a gear set related?...

question

Engineering, 26.07.2019 17:20

You need to design a compound reverted gear train with a 25: 1 gear ratio. (a) explain how you would go about developing this design. (b) if you were...

question

Engineering, 26.07.2019 17:20

One of the following is an extensive property: a)- density b)- volume c)- pressure d)-none of the above...

question

Engineering, 26.07.2019 17:20

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

question

Engineering, 26.07.2019 17:20

Tool wear rate decreases with increasing: i. machining velocity and work material hardness. ii. cutting tool hardness. ii. none of the above. iv. not...

question

Engineering, 26.07.2019 17:20

Define the following terms. a drawing with the terms labeled would also be where appropriate. a. pitch circle/pitch diameter b. pinion/gear c. base c...

More questions: Chemistry Another questions

Questions on the website: 13722361