Chemistry, 02.09.2019 00:30 4300402428

If the concentration of the stock solution is 25 m, what would be the dilution factor and concentration of sample ‘c’ with respect to original stock solution?

Answers: 1

Show answers

Answers

Answer from: friezaforceelite

The dilution factor = 5 and concentration of sample ‘c’ = 5M

Further explanation

Dilution is the process of adding solvents (generally water) which aims to obtain a solution with a concentration that is smaller than the initial concentration of a more concentrated substance.

So the principle of dilution is to get lower concentration.

In dilution the number of dissolved moles before and after dilution is the same

The dilution formula is as follows:

$\large {\boxed {M_1 \: \times \: V_1 ~ = ~ M_2 \: \times \: V_2}}$

M1 = Molarity of the solution before dilution

V1 = volume of the solution before dilution

M2 = Molarity of the solution after dilution

V2 = Molarity volume of the solution after dilution

Dilution factors are factors that must be included / multiplied in the calculation formula, usually to find the percentage of substances

So the dilution factor is the division of the final volume by the initial volume.

Formula used:

$\large{\boxed{\bold{DF=\frac{Vf}{Vi}}}}$

Vf = final volume

Vi = initial volume

The dilution factor is used as the denominator of a fraction.

For example, a DF of 10 means a 1:10 dilution.

This is different from the term "diluted 10 x or 100 x" then what is multiplied is the initial volume before dilution, so if it is diluted 10 x it means the concentration after dilution = initial concentration divided by 10

If the concentration of the stock solution is 25 m, the dilution factor:

20 ml of sample

100 ml final volume

So DF = 100/20 = 5

Then

concentration of solution C = 1/5 x 25 = 5 M

Learn more

The molarity of the stock solution of luminol

link

NaOH solution

link

Delta H solution

link

Keywords: stock solution, Dilution factors, dilution, concentration

If the concentration of the stock solution is 25 m, what would be the dilution factor and concentrat

Answer from: Quest

answer: the rate of diffusion increases with increase in temperature.

increase in temperature, increases the molecular/particles speed (kinetic energy. diffusion means movement of particles through the material.

generally, the heavier the particle the more it interacts with the environment and more the temperature matters. so higher temperature results in higher diffusion.

Answer from: Quest

the answer is option a.

Another question on Chemistry

Chemistry, 21.06.2019 22:00

Bohr's model could only explain the spectra of which type of atoms? single atoms with one electron single atoms with more than one electron bonded atoms with one electron bonded atoms with more than one electron

Answers: 2

Answer

Chemistry, 21.06.2019 22:00

To save time, you can approximate the initial mass of the solid to the nearest ±1 g. for example, if you are asked to add 14.3 g of copper, add between 13 g and 15 g. which of the following sets include two samples with an equal density? which all that apply below 15.4 g gold and 18.7 g silver 15.2 g copper and 50.0 g copper 20.2 g silver and 20.2 g copper 11.2 g gold and 14.9 g gold

Answers: 1

Answer

Chemistry, 22.06.2019 00:00

What stress will shift the following equilibrium system to the left? n2(g) + 3h2(g) ⇌ 2nh3(g) adding more n2(g) adding more nh3(g) increasing the pressure of the system reducing the volume of the container

Answers: 1

Answer

Chemistry, 22.06.2019 16:10

Given the following equation: 2a1 + 3mgcl2 --> 2alcl3 + 3mg how many moles of aluminum chloride are produced from 2.5 moles of magnesium chloride?

Answers: 1

Answer

You know the right answer?

If the concentration of the stock solution is 25 m, what would be the dilution factor and concentrat...

Questions