Computers and Technology, 16.04.2021 14:00 katelynamber10

The Scenario A friend is helping set up a new office for a physician and would like your help planning the network. Here are the requirements: There should be one server, which will contain the software that manages the medical practice. All staff devices should be able to connect to the network to access the server. All staff devices should be able to access the internet. Every part of the office, including the waiting area, should have good access to WiFi. The three exam rooms, the reception area, and the office should each have an Ethernet jack installed in a wall to allow for optional wired network access. What Is Already Done Here is what your friend has already accomplished on the project: Internet service has already been set up for the building, with a cable modem installed in the office. The following hardware has already been purchased but not yet installed: a server a WiFi-capable router with six Ethernet ports on it the hardware needed to install the Ethernet jacks enough Ethernet cable to make all needed connections Your Task Your task is to decide where the networking hardware will be placed for optimal effectiveness. Think about the requirements in the scenario above and examine the floorplan image provided. Your teacher may require you to work with a partner. Be sure to ask before you begin the project. Use this floorplan image for your project. Mark up the floor plan as follows: Draw a purple rectangle where the wireless router should be placed. Keep in mind the following: A wireless router's signal can extend for up to 125 feet in all directions, but the signal starts to get weak at a much shorter distance. Be mindful of the measurements listed around the perimeter of the floor plan when placing your router. If you place the router in a corner of the building, not all areas of the building will have a strong WiFi signal. You can place the router in the ceiling to keep it out of the way. Draw a blue rectangle where the cable modem will sit. Keep in mind the following: The cable modem should be so

Answers: 1

Show answers

Another question on Computers and Technology

Computers and Technology, 22.06.2019 18:30

The "instance" relationship shows that something is an object of a

Answers: 1

Answer

Computers and Technology, 23.06.2019 02:30

Experimental data that is expressed using numbers is said to be

Answers: 1

Answer

Computers and Technology, 23.06.2019 19:00

Now youâ€™re on your own. include a short summary of this section with plots in your lab report. write a matlab script file to do steps (a) through (d) below. include a listing of the script file with your report. 1 the soundsc(xx,fs) function requires two arguments: the first one (xx) contains the vector of data to be played, the second argument (fs) is the sampling rate for playing the samples. in addition, soundsc(xx,fs) does automatic scaling and then calls sound(xx,fs) to actually play the signal. mcclellan, schafer, and yoder, dsp first, 2e, isbn 0-13-065562-7. prentice hall, upper saddle river, nj 07458. c 2015 pearson education, inc. 4 mcclellan, schafer and yoder, signal processing first. prentice hall, upper saddle river, new jersey, 2003. c 2003 prentice hall. (a) generate a time vector (tt) to cover a range of t that will exhibit approximately two cycles of the 4000 hz sinusoids defined in the next part, part (b). use a definition for tt similar to part 2.2(d). if we use t to denote the period of the sinusoids, define the starting time of the vector tt to be equal to t , and the ending time as ct . then the two cycles will include t d 0. finally, make sure that you have at least 25 samples per period of the sinusoidal wave. in other words, when you use the colon operator to define the time vector, make the increment small enough to generate 25 samples per period. (b) generate two 4000 hz sinusoids with arbitrary amplitude and time-shift. x1.t / d a1 cos.2

Answers: 1

Answer

Computers and Technology, 24.06.2019 17:40

Create a file called favorite_foods, and list your favorite foods, entering five or six or more. press enter after each favorite food so it appears on its own line (make certain you also press enter after the final food item). after the file is created, add two more foods you like that are not on the list (press enter after the final food item). view the list of foods to make certain the two items you added appear at the end of the list

Answers: 2

Answer

You know the right answer?

The Scenario A friend is helping set up a new office for a physician and would like your help planni...

Questions