![subject](/tpl/images/cats/User.png)
Engineering, 30.08.2019 22:20 MaxxL
Asolid round bar with diameter of 50-mm has a groove cut to a diameter of 45-mm, with a radius of 2.5-mm. the bar is not rotating. the bar is loaded with a repeated bending load that causes the bending moment at the groove to fluctuate between 0 and 2825 n-m. the bar is hot-rolled aisi 1095, but the groove has been machined. a) determine the factor of safety for fatigue based on infinite life and b) determinethe factor of safety for yielding.
![ansver](/tpl/images/cats/User.png)
Answers: 1
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 23:20
Two technicians are discussing the intake air temperature (iat) sensor. technician a says that the computer uses the iat sensor as a backup to the engine coolant temperature (ect) sensor. technician b says that the powertrain control module (pcm) will subtract the calculated amount of fuel if the air measures hot. who is correct
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 16:10
An electrical motor raises a 50kg load at a construct velencity .calculate the power of the motor, if it takes 40sec to raise the load through a height of 24m(take g =9.8n/g)
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Ariver flows from north to south at 8 km/h. a boat is to cross this river from west to east at a speed of 20 km/h (speed of the boat with respect to the earth/ground). at what angle (in degrees) must the boat be pointed upstream such that it will proceed directly across the river (hint: find the speed of the boat with respect to water/river)? a 288 b. 21.8 c. 326 d. 30.2
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
You know the right answer?
Asolid round bar with diameter of 50-mm has a groove cut to a diameter of 45-mm, with a radius of 2....
Questions
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
English, 10.11.2019 16:31
![question](/tpl/images/cats/mat.png)
Mathematics, 10.11.2019 16:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/ap.png)
Advanced Placement (AP), 10.11.2019 16:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 10.11.2019 16:31
![question](/tpl/images/cats/ekonomika.png)
Business, 10.11.2019 16:31
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mkx.png)
Arts, 10.11.2019 16:31
![question](/tpl/images/cats/mat.png)
Mathematics, 10.11.2019 16:31