Engineering, 14.11.2019 05:31 sammuelanderson1371

Agas containing water vapor has a dry-basis composition of 7.5 mole% co, 11.5% co2, 0.5% o2, and 80.5% n2. the gas leaves a catalyst regeneration unit at 620°c and 1 atm with a dew point of 57°c at a flow rate of 28.5 scmh [m3(stp)/h]. valuable solid catalyst particles entrained in the gas are to be recovered in an electrostatic precipitator, but the gas must first be cooled to 425°c to prevent damage to the precipitator electrodes. the cooling is accomplished by spraying water at 20°c into the gas. use simultaneous material and energy balances on the spray cooler to calculate the required water feed rate (kg/h). treat the spray cooler as adiabatic and neglect the heat transferred from the entrained solid particles as they cool. in terms that a high school senior could understand, explain the operation of the spray cooler in this problem. (what happens when the cold water contacts the hot gas? )

Answers: 2

Show answers

Another question on Engineering

Engineering, 03.07.2019 14:10

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Abrake has a normal braking torque of 2.8 kip in and heat-dissipating cast-iron surfaces whose mass is 40 lbm. suppose a load is brought to rest in 8.0 s from an initial angular speed of 1600 rev/min using the normal braking torque; estimate the temperature rise of the heat dissipating surfaces.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

The thermal expansion or contraction of a given metal is a function of the f a)-density b)-initial temperature c)- temperature difference d)- linear coefficient of thermal expansion e)- final temperature f)- original length

Answers: 2

Answer

Engineering, 04.07.2019 19:20

Acommercial grade cubical freezer, 4 m on a side, has a composite wall consisting of an exterior sheet of 5.0-mm thick plain carbon steel (kst= 60.5 w/m k), an intermediate layer of 100-mm thick polyurethane insulation (kins 0.02 w/m k), and an inner sheet of 5.0- mm thick aluminium alloy (kal polyurethane insulation and both metallic sheets are each characterized by a thermal contact resistance of r 2.5 x 104 m2 k/w. (a) what is the steady-state cooling load that must be maintained by the refrigerator under conditions for which the outer and inner surface temperatures are 25°c and -5°c, respectively? (b) for power saving purpose, which wall material should be increased/reduced in. thickness in order to reduce 50% of the cooling load found in part (a)? redesign the thickness of the proposed material. 177 w/m-k). adhesive interfaces between the q=575.93 w

Answers: 2

Answer

You know the right answer?

Agas containing water vapor has a dry-basis composition of 7.5 mole% co, 11.5% co2, 0.5% o2, and 80....

Questions