Engineering, 16.12.2019 02:31 lilyrockstarmag

When you can do it safely, instead of relying heavily on your brakes. a. use your emergency brake b. roll through stop signs c. coast to a stop d. weave side to side

Answers: 3

Show answers

Answers

Answer from: aly02

A. Use your emergency brake

Explanation:

The function of the handbrake is to immobilize the vehicle. If we forget it when parking, we run the risk of the car moving with any contact. For example, if another vehicle hits you from behind, it could move causing an accident or hitting the car in front.

Do not forget to remove the handbrake before starting. If we drive with the handbrake on, the clutch and brakes will wear quickly. Similarly, it is not advisable to use it when hydraulic brakes fail, and less if the vehicle is going at high speed.

The best way to care for the handbrake is to use it only when parking the vehicle. The handbrake has cables that allow pressure on the wheel brakes, and this helps the hydraulic brakes not wear out. In turn, vehicles with disc brakes on the rear wheels have a mechanism called a self-adjuster, which keeps the brake pads aligned avoiding wear.

If we feel any annoying sound when braking, or the braking distance is longer than usual, there is probably a problem with the brake pads. The handbrake and hydraulic brake work under different mechanisms, so whenever you feel that there is a problem with braking, you should consult the mechanic.

If the car is automatic, when is the parking brake used? In the case of cars with automatic transmission, when parking the car is at P and the transmission is immobilized. If the vehicle is on a flat surface, this part exerts little pressure, but if it is on a slope, the entire weight of the vehicle rests on the brake and the transmission itself, therefore the parking brake must be applied.

Answer from: thebrain1345

coast to a stop

Explanation:

Emergency brakes are only for emergencies (and will not increase fuel efficiency). When you can do it safely, coast to a stop instead of relying heavily on your brakes. If you can see a red light ahead, there's no point in maintaining your speed all the way up to the braking point: you'll still have to sit behind the light until it changes. Instead, try taking your foot off the accelerator and coasting to a stop. You'll still need to brake at the end, but you'll use less gas and add less wear and tear to your brakes.

Answer from: Quest

D) the pirates , that’s the answer

Answer from: Quest

no he didnt use it

explanation:

he said no

Another question on Engineering

Engineering, 03.07.2019 14:10

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10

Answers: 1

Answer

Engineering, 04.07.2019 19:10

An engine, weighing 3000 n, is supported on a pedestal mount. it has been observed that the engine induces vibration into the surrounding area through its pedestal at the maximum operating speed. determine the stiffness of the dynamic vibration absorber spring in (n/m) that will reduce the vibration when mounted on the pedestal. the magnitude of the exciting force is 250 n, and the amplitude of motion of the auxiliary mass is to be limited to 2 mm note: in this question type-in right numbers, no decimals, no fractions, no unit. approximate to right number if needed

Answers: 3

Answer

You know the right answer?

When you can do it safely, instead of relying heavily on your brakes. a. use your emergency brake b...

Questions