subject
Engineering, 20.12.2019 23:31 Tyrant4life

Consider a wastewater effluent (qw = 1 m/s) with a lo = 75 mg/l and 2.0 mg/l of dissolved oxygen that is discharged into a river that has a flow rate of 8.7 m/s and a flow velocity of 2.0 ft/sec. the river just upstream of the discharge has a dissolved oxygen concentration of 7.0 mg/l and a lo of 4.7 mg/l. the temperature of the river is 15 °c and the temperature of the wastewater discharge is 24.7 °c. the deoxygenation rate constant (base e) is 0.20 d at 20°c; the reaeration rate constant (base e) is 0.50 dat 20 °c. the bod rate constant (base e) is 0.20 d at 20 °c. assume that the thetas for rate constant temperature corrections are 1.047 for all rate constants. assume sea level and fresh water conditions. a. determine the initial oxygen deficit (mg/l) and the ultimate bod, lo (mg/l) just downstream from the discharge after blending b. the time (days) and distance (miles) to reach the minimum dissolved oxygen concentration. c. the minimum dissolved oxygen concentration (mg/l) d. the dissolved oxygen that could be expected 50 miles downstream from the discharge (mg/l). e. use excel to create a graph of do vs. time. note that this is y vs. x. be sure to label the y and x axis including units and show the excel spreadsheet used to create your graph. the work you show in your calculation in partc will serve as your sample calculation.

ansver
Answers: 3

Another question on Engineering

question
Engineering, 04.07.2019 18:10
Afluid flows with a velocity field given by v=(x/t)i.. determine the local and convective accelerations when x=3 and t=1.
Answers: 2
question
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
question
Engineering, 04.07.2019 18:10
Ahot wire operates at a temperature of 200°c while the air temperature is 20°c. the hot wire element is a tungsten wire of 5 um diameter and 2 mm in length. plot using excel current, heat transfer and heat generated by the wire for air velocity varying from 1-10 m/s in steps of lm/s? matlab the sensor voltage output, resistance, or assume nu 0.989 re033pr13 take air properties at tr (200°c20°c)/2 = 110°c properties of tungsten: c 0.13 kj/kg.k 3 p 19250 kg/m k (thermal conductivity) = 174 w/m.k
Answers: 2
question
Engineering, 04.07.2019 18:20
Agas mixture consists of 8 kmol of h2 and 2 kmol of n2. determine the mass of each gas and the apparent gas constant of the mixture.
Answers: 3
You know the right answer?
Consider a wastewater effluent (qw = 1 m/s) with a lo = 75 mg/l and 2.0 mg/l of dissolved oxygen tha...
Questions
question
Health, 29.10.2020 21:30
question
Mathematics, 29.10.2020 21:30
question
Social Studies, 29.10.2020 21:30
question
Mathematics, 29.10.2020 21:30
question
Biology, 29.10.2020 21:30
question
Mathematics, 29.10.2020 21:30
Questions on the website: 13722360