subject
Engineering, 18.02.2020 21:45 kay4358

One challenge for architects is that the design created today will require several years of implementation, verification, and testing before appearing on the market. This means that the architect must project what the technology will be like several years in advance. Sometimes, this is difficult to do. a) According to the trend in device scaling historically observed by Moore’s law, the number of transistors on a chip in 2028 should be how many times the number in 2018? (You may assume a 40% increase in the number of transistors per year.)b) The increase in performance once mirrored this trend. Had performance continued to climb at the same rate as in the 1990s, approximately what performance would chips have over the VAX-11/750 in 2028 (assume a 40% increase in performance per year)? You may assume that the speedup in the year 2003 over the VAX-11/750 is 6043x. c) At the current rate of increase of the mid-2000s (assume 22% per year), what is a more updated projection of performance in 2028? You may assume that the speedup in the year 2010 over the VAX-11/750 is known to be 24,129.d) What has limited the rate of growth of the clock rate, and what are architects doing with the extra transistors to increase performance?e) The rate of growth for DRAM capacity has also slowed down. For 20 years, DRAM capacity improved 60% each year. If 8 Gbit DRAM was first available in 2015 and 16 Gbit DRAM was not available until 2019, what is the current DRAM growth rate?

ansver
Answers: 1

Another question on Engineering

question
Engineering, 04.07.2019 18:10
Refrigerant 134a enters an insulated compressor operating at steady state as saturated vapor at -26°c with a volumetric flow rate of 0.18 m3/s. refrigerant exits at 9 bar, 70°c. changes in kinetic and potential energy from inlet to exit can be ignored. determine the volumetric flow rate at the exit, in m3/s, and the compressor power, in kw.
Answers: 1
question
Engineering, 04.07.2019 18:10
Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.
Answers: 3
question
Engineering, 04.07.2019 18:10
Water at the rate of 1 kg/s is forced through a tube with a 2.5 cm inner diameter. the inlet water temperature is 15°c, and the outlet water temperature is 50°c. the tube wall temperature is 14°c higher than the local water temperature all along the length of the tube. what is the length of the tube?
Answers: 3
question
Engineering, 04.07.2019 18:10
The flow rate of air through a through a pipe is 0.02 m5/s. a pitot static tube is placed in the flow. the radius of the pitot static tube is 1 mm. assuming the flow to be steady and the air to be at 300k, calculate the difference in total and static pressure if the diameter of the pipe is: (a) d 0.1 m d 0.05 m (c) d 0.01 m
Answers: 2
You know the right answer?
One challenge for architects is that the design created today will require several years of implemen...
Questions
question
Social Studies, 01.02.2021 15:50
question
English, 01.02.2021 15:50
question
Social Studies, 01.02.2021 15:50
Questions on the website: 13722362