Engineering, 10.03.2020 09:03 wildfire771003

Your boss needs to recommend either the in-situ soil or the borrow material. Although you do not have much background on soil behavior, what is your recommendation?
In providing your recommendation, you want to consider constructability issues (such as ease of compaction, moisture content). Without doing any additional tests, and based on your experience with soils, what compaction conditions would you suggest to achieve low permeability? What compaction conditions would you recommend to reduce soil expansion (swelling)?

Table 1 Compaction Characteristics of Selected Soils.
Borrow Soil In-Situ Soil
STANDARD MODIFIED STANDARD MODIFIED
PROCTOR PROCTOR PROCTOR PROCTOR
Dry Unit Water Dry Unit Water Dry Unit Water Dry Unit Water
Weight Content Weight Content | Weight Content Weight content
Yd (kN/m³) w(%) Yd (kN/m³) w(%) Yd (kN/m³) w(%) Yd (kN/m³) w(%)
16.68 8.4 17.58 5.7 15.63 12.7 15.72 10.4
18.79 9.7 20.02 7.4 17.72 14.4 18.76 12.2
S3? S3? 20.60 9.3 17.46 16.0 18.64 14.0
18.62 13.4 19.62 11.3 17.15 16.7 18.15 15.0
18.05 15.0 18.93 13.0 16.30 18.2 17.48 16.4

Answers: 1

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise

Answers: 3

Answer

Engineering, 04.07.2019 18:20

Apiston-cylinder device contains 0.1 m3 of liquid water and 0.9 m3 of water vapor in equilibrium at 800 kpa. heat is transferred at constant pressure until the temperature of water reaches 350 °c. determine (a) the quality of water at the initial state (b) the work associated with this process, (c) the heat associated with this process.

Answers: 2

Answer

Engineering, 04.07.2019 18:20

A2-m rigid tank initially contains saturated water vapor at 100 kpa. the tank is connected to a supply line through a valve. steam is flowing in the supply line at 600 kpa and 300 c. the valve is opened, and steam is allowed to enter the tank until the pressure in the tank reaches the line pressure, at which point the valve is closed. a thermometer placed in the tank indicates that the temperature at the final state is 200°c. determine (a) the mass of steam that has entered the tank (b) the amount of heat transfer.

Answers: 3

Answer

Engineering, 06.07.2019 04:10

Aheat pump with refrigerant-134a as the working fluid is used to keep a space at 25°c by absorbing heat from geothermal water that enters the evaporator at 500c at a rate of 0.065 kg/s and leaves at 40°c. the refrigerant enters the evaporator at 20°c with a quality of 23 percent and leaves at the inlet pressure as saturated vapor. the refrigerant loses 300 w of heat to the surroundings as it flows through the compressor and the refrigerant leaves the compressor at 1.4 mpa at the same entropy as the inlet. determine: (a) the degrees of subcooling of the refrigerant in the condenser, b)-the mass flow rate of the refrigerant . (c) the heating load and the cop of the pump, and d)-the theoretical minimum power input to the compressor for the same heating load.

Answers: 3

Answer

You know the right answer?

Your boss needs to recommend either the in-situ soil or the borrow material. Although you do not hav...

Questions