Engineering, 24.03.2020 21:30 arielpraczko1

A 26-tooth pinion rotating at a uniform 1800 rpm meshes with a 55-tooth gear in a spur gear reducer. Both pinion and gear are manufactured to a quality level of 10. The transmitted tangential load is 22 kN. Conditions are such that Km = 1.7. The teeth are standard 20-degree, full-depth. The module is 5 and the face width 62 mm. Determine the bending stress when the mesh is at the highest point of single tooth contact.

Answers: 1

Show answers

Answers

Answer from: ayoismeisalex

The bending stress of the face tooth is $\sigma _{bg} = 502.82 MPa$

Explanation:

From the question we are told that

The number of tooth of the pinion is $N_t = 26 \ tooth$

The velocity of rotation is given as $\omega_p = 1800 rpm$

The number of tooth is of the gear is $N_g = 55 \ tooth$

The quality level is Q_r = 10

The transmitted tangential load is $F_T = 22\ kN$ = $22 KN * \frac{1000N}{1KN} = 22*10^3 N$

k_m = 1.7

The angle of the teeth is $\theta_t = 20^o$

The module is M= 5

The face width is W_f = 62mm

The diameter of the pinion is mathematically represented as

d_p = M * N_t

Substituting the values

d_p = 5 *26

$= 130 mm = \frac{130}{1000} = 0.130m$

The pitch line velocity is mathematically represented as

$V_t = \frac{d_p }{2} \frac{2 \pi \omega_p}{60}$

Substituting values

$= \frac{0.130}{2} * \frac{2 * 3.142 * 1800 }{60}$

$= 12.25\ m/s$

Generally the dynamic factor is mathematically represented as

$K_v = [\frac{A}{A +\sqrt{200V_t} } ]^B$

Now B is a constant that is mathematically represented as

$B = \frac{(12 -Q_r )^{2/3}}{4}$

substituting values

$= \frac{(12- 10 )^{2/3}}{4}$

=0.3968

A is also a constant that is mathematically represented as

A = 50 + 56(1 -B)

Substituting values

= 50 +56 (1- 0.3968)

= 83.779

Substituting these value into the equation for dynamic factor we have

$K_v = [\frac{83.779}{83.779 + \sqrt{200 * 12.25} } ]^{0.3968}$

= 0.831

The geometric bending factor for a 20° profile from table

"AGMA Bending Geometry Factor J for 20°, Full -Depth Teeth with HPSTC Loading , Table 2-9"

That corresponds to 55 tooth gear meshing with 26 pinion is

J_g = 0.41

the diameter pitch can be mathematically represented as

$p_d = \frac{1}{M}$

Substituting values

$p_d = \frac{1}{5}$

$=0.2mm^{-1}$

The mathematically representation for gear tooth bending stress in the teeth face is as follows

$\sigma_{bg} = \frac{F_T \cdot p_d }{W_f * J_g}\frac{K_a K_{dt} }{K_v} K_s K_B K_t ----(1)$

Where W_t is the tangential load

W_f is the face width

K_a is the application factor this is obtained from table "Application Factors, Table 12-17 " and the value is K_a = 1

$K_{dt}$ is the load distributed factor

K_s is the size factor

K_B is the rim thickness factor which is obtained for M which has a value 1

K_t is the idler

Substituting values into equation 1

$\sigma_{bg} = \frac{22*10^3 *0.2}{62 * 0.41} * \frac{1 * 1.7 }{0.831} * 1 *1 *1.42$

= 502.82 N/mm^2

$= 502.82 * 1000 * \frac{N}{m^2}$

= 502.82 MPa

Answer from: Quest

Do you need to draw this out?

Answer from: Quest

answer: make you irritable

Another question on Engineering

Engineering, 03.07.2019 14:10

Amass of 1.5 kg of air at 120 kpa and 24°c is contained in a gas-tight, frictionless piston-cylinder device. the air is now compressed to a final pressure of 720 kpa. during the process, heat is transferred from the air such that the temperature inside the cylinder remains constant. calculate the boundary work input during this process.

Answers: 2

Answer

Engineering, 03.07.2019 15:10

Ahouse has the following electrical appliance usage (1) single 40w lamp used for 4 hours per day (2) single 60w fan used for 12 hours per day (3) single 200w refrigerator that runs 24 hours per day with compressor run 12 hours and off 12 hours find the solar power inverter size in watt with correction factor of 1.25.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Water at 70°f and streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream. 0 psia is heated in a chamber by mixing it with saturated water vapor at 20 psia. if both streams enters the mixing chamber at the same mass flow rate, determine the temperature and the quality of the existing system.

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Burgers vector is generally parallel to the dislocation line. a)-true b)-false

Answers: 2

Answer

You know the right answer?

A 26-tooth pinion rotating at a uniform 1800 rpm meshes with a 55-tooth gear in a spur gear reducer....

Questions