subject
Engineering, 07.04.2020 15:28 zanaplen27

Eagletrons are all-electric automobiles produced by Mogul Motors, Inc. One of the concerns of Mogul Motors is that the Eagletrons be capable of achieving appropriate maximum speeds. To monitor this, Mogul executives take samples of ten Eagletrons at a time. For each sample, they determine the average maximum speed and the range of the maximum speeds within the sample. They repeat this with 35 samples to obtain 35 sample means and 35 ranges. They find that the average sample mean is 103.50 miles per hour, and the average range is 4.00 miles per hour. Using these results, the executives decide to establish an R-chart. They would like this chart to be established so that when it shows that the range of a sample is not within the control limits, there is only approximately a 0.0027 probability that this is due to natural variation. The control limits for the chart based on the above requirement for the given information are: UCL Subscript Upper R overbar = nothing miles per hour (round the reponse to three decimal places). amison Kovach Supply Company manufactures paper clips and other office products. Although inexpensive, paper clips have provided the firm with a high margin of profitability. Sample size is 200 . Results are given for the last 10 samples. Sample 1 2 3 4 5 6 7 8 9 10 Defectives 4 8 3 5 6 5 4 5 2 11 The type of control chart that is best to monitor this process is ▼ c minus chart x overbar minus chart p minus chart. Eagletrons are all-electric automobiles produced by Mogul Motors, Inc. One of the concerns of Mogul Motors is that the Eagletrons be capable of achieving appropriate maximum speeds. To monitor this, Mogul executives take samples of ten Eagletrons at a time. For each sample, they determine the average maximum speed and the range of the maximum speeds within the sample. They repeat this with 35 samples to obtain 35 sample means and 35 ranges. They find that the average sample mean is 103.50 miles per hour, and the average range is 4.00 miles per hour. Using these results, the executives decide to establish an R-chart. They would like this chart to be established so that when it shows that the range of a sample is not within the control limits, there is only approximately a 0.0027 probability that this is due to natural variation. The control limits for the chart based on the above requirement for the given information are: UCL Subscript Upper R overbar = nothing miles per hour (round the reponse to three decimal places). amison Kovach Supply Company manufactures paper clips and other office products. Although inexpensive, paper clips have provided the firm with a high margin of profitability. Sample size is 200 . Results are given for the last 10 samples. Sample 1 2 3 4 5 6 7 8 9 10 Defectives 4 8 3 5 6 5 4 5 2 11 The type of control chart that is best to monitor this process is ▼ c minus chart x overbar minus chart p minus chart.

ansver
Answers: 2

Another question on Engineering

question
Engineering, 03.07.2019 14:10
Line joining liquid phase with liquid and solid phase mixture is known as: a) liquidus b) solidus c) tie line d) none of the mentioned
Answers: 2
question
Engineering, 04.07.2019 18:10
Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise
Answers: 3
question
Engineering, 04.07.2019 18:10
Calculate the bore of a cylinder that has a stroke of 18 inches and an extension time of 6 seconds at a flow rate of 4 gal/min.
Answers: 3
question
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
You know the right answer?
Eagletrons are all-electric automobiles produced by Mogul Motors, Inc. One of the concerns of Mogul...
Questions
question
Mathematics, 11.03.2021 22:50
question
Mathematics, 11.03.2021 22:50
question
Business, 11.03.2021 22:50
question
Biology, 11.03.2021 22:50
Questions on the website: 13722359