subject
Engineering, 07.04.2020 22:44 dondre54

In this task, you will complete and submit an individual proposal. In your proposal, you should include the first two elements of your final project: a case needs analysis and a relational database model. Use what you have discussed in your collaborative groups to finalize your proposal. This will be graded with the Milestone Three Rubric. Specifically, the following critical elements must be addressed in your submission: I. Case Needs Analysis: Determine the data requirements of Birchwood Lane Schools.
a. What data from the scenario is needed for the database and why?
b. To what extent is additional information needed to develop complete data requirements? II. Relational Database Model
a. Based on the requirements you have determined, propose a relational database model. Be sure to include applicable entities and proper relationship mapping.
b. Propose a logical database model based on the entities present in your visual conceptual database model.
The final project for this course is the creation of a database proposal and implementation plan report that will address the needs of a given scenario. The purpose of this assessment is to assess the students’ understanding of simple database structure, functions, and terminology from an information management perspective. You are to design a simple database framework that addresses the needs of Birchwood Lane Schools and the development of a strategy for implementing that database. Your submissions will include the relational database model you have designed, including diagrams (e. g., Microsoft Visio), a plan for implementation, and a persuasive presentation to stakeholders, in this case the Birchwood Lane School Board. The persuasive presentation will build off the work completed for this database proposal and implementation plan report and is due in Module Eight. For more details about the presentation, reference the "Final Presentation Guidelines and Rubric" document in the Assignment Guidelines and Rubrics section of the course. The project is supported by four formative milestones, which will be submitted at various points throughout the course to scaffold learning and ensure quality final submissions. These milestones will be submitted in Modules Two, Three, Four, and Five. The final submission of your database proposal and implementation plan report will occur in Module Seven.

ansver
Answers: 2

Another question on Engineering

question
Engineering, 04.07.2019 18:10
Acompressor receives the shaft work to decrease the pressure of the fluid. a)- true b)- false
Answers: 3
question
Engineering, 06.07.2019 02:30
An electric motor is used to drive a power press which makes steel turning moment diagrams 323 pressings from a metal sheet. the motor runs at a mean speed of 50 rev/s. the torque required is 10.0nm for 0.2s, followed by 1.0nm for0.3 s with this sequence then being repeated. what is the minimum power required of the motor and the moment of incrtia required for the t1ywhcel if the speed fluctuations are to be restricted to 1.5%?
Answers: 3
question
Engineering, 06.07.2019 04:10
An array of m-50 thermoelectric modules is installed on the exhaust of a sports car. each module has an effective seebeck coefficient of sp of 0.143 5vk and an internal electrical resistance of r.-4 ? in addition, : (15 points each module is of width w 60mm and contains n=100 pairs of semiconducting pellets. each pellet hasan overall length of 2l-5mm and a cross-sectional area as 1.2 x 10'm and is characterized by a thermal conductivity of kpl2w rnk. the hot side of each module is exposed to exhaust gases at·p650c with hia4ow rrk while the osite side of each module is cooled by pressurized water at surface) and 156 °c (at the cool surface). 11s c with h: -500w/m'k. the modules are wired n series and the load resistance is r d=400ohm .the module surface temperatures, t, and ts are 183 "c (at the hot surface and 156c (at the cool surface) a)-draw a schematic of this scenario and label all parts. a. b. if the induced current, i, is 0.15 amps, what is the total power (pa) for one module? c. what is the total power harvest from the exhaust with all 50 modules?
Answers: 2
question
Engineering, 06.07.2019 04:20
Explain the similarities and differences in the design guidelines for turning and for
Answers: 1
You know the right answer?
In this task, you will complete and submit an individual proposal. In your proposal, you should incl...
Questions
question
Mathematics, 24.02.2020 02:17
question
Mathematics, 24.02.2020 02:18
question
Mathematics, 24.02.2020 02:18
question
Mathematics, 24.02.2020 02:18
question
Mathematics, 24.02.2020 02:22
question
Biology, 24.02.2020 02:22
Questions on the website: 13722360