Engineering, 14.04.2020 23:47 Dreynolds1667

Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220 °C flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3 m/s.
If the flat plate surface temperature is maintained at 80 °C, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.

Answers: 2

Show answers

Answers

The local convection heat transfer coefficient at 1 m from the leading edge is $0.44 \frac{W}{m^{2} \times K}$ , the average convection heat transfer coefficient over the entire plate is $0.293 \frac{W}{m^{2} \times K}$ and the total heat flux transfer to the plate is 61.6 KJ .

Explanation:

It is case of heat and mass transfer in which due to temperature difference between gas and surface. Further temperature boundary layer will developed on flat plate in longitudinal direction.

Hot carbon dioxide exhaust gas

physical properties

$r= 1.05 \frac{kg}{m^{3}}$

$c_p = 1.02 \frac{kJ}{Kg \times K}$

$m= 231 \times 10^{7} \frac{N \times s }{m^2}$

υ = $21.8 \times 10^{6} \frac{m^2}{s}$

$k = 32.5 \times 10^{3} \frac{W}{m \times K}$

$\alpha = 30.1 \times 10^{6} \frac{m^{2}}{s}$

Pr = 0.725

Apart from these other data arr given below,

$v= 3 \frac{m}{s} \\ p= 1 atm \\ L_c = 1.5m \\T_g= 220 C \\ T_s = 80 C$

To find the local convection heat transfer coefficient at 1 m from the leading edge, we use correlation used for laminar flow over flat plate,

$Nu = \frac{ h \times L }{k} = 0.332 \times (Re^{\frac{1}{2} }) \times (Pr^{\frac{1}{3} })$

where h= Average heat transfer coefficient

L= Length of a plate

k= Thermal Conductivity of carbon dioxide

Re = Reynold's Number

Pr = Prandtle Number

(a) Convection heat transfer coefficient at 1 m from the leading edge

is referred as local convection heat transfer coefficient.

To find convection heat transfer coefficient at 1 m from leading edge,

$Nu = \frac{ h_local \times L }{k} = 0.332 \times (Re^{\frac{1}{2} }) \times (Pr^{\frac{1}{3} })$

Here, first we have to find Re and Pr,

$Re = \frac{r \times v \times L}{m}$

$Re = \frac{1.0594 \times 3 \times 1}{231 \times 10^{7}}$

$Re = 20.63 \times 10^{-10}$

Pr number is take from physical property data and Pr is 0.725.

Putting value of Re and Pr in main equation,

we get

$Nu = \frac{ h_local \times 1 }{32.5 \times 10^{3}} = 0.332 \times ( (20.63 \times 10^{-10})^{\frac{1}{2} }) \times (0.725^{\frac{1}{3} })$

$h_local = 32.5 \times 10^{3} \times 0.332 \times ( (20.63 \times 10^{-10})^{\frac{1}{2} }) \times (0.725^{\frac{1}{3} })$

$h_local = 0.44 \frac{W}{m^{2} \times K}$

(b) To find average convection heat transfer coefficient,

it can be find out as case (a), only difference is that instead of L=1 m, L=1.5 m would come,

Therefore,

$Nu = \frac{ h \times 1.5 }{32.5 \times 10^{3}} = 0.332 \times ( (20.63 \times 10^{-10})^{\frac{1}{2} }) \times (0.725^{\frac{1}{3} })$

Finally,

$h = \frac{0.44}{1.5}$

$h = 0.293 \frac{W}{m^{2} \times K}$

$Q = h \times (T_g - T_s)$

$Q = 0.293 \times (220-80) \\ Q= 0.293 \times 140 \\ Q= 61.6 KJ$

Answer from: Quest

answer:

i cant give me a pic

explanation:

Answer from: Quest

answer: copyright is extremely important to authors because it constitutes the ownership of one's original work. having ownership means you can protect your work as intellectual property and control who makes money from it—which is you and those to whom you assign rights.

Another question on Engineering

Engineering, 04.07.2019 18:10

Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.

Answers: 1

Answer

Engineering, 04.07.2019 18:20

Inadequate stores control is not an obstacle to effective work order system. (clo4) a)-true b)-false

Answers: 3

Answer

Engineering, 04.07.2019 18:20

Modern high speed trains do not have perpendicular expansion gaps where rails are joined end-to-end any more they are mostly welded together but what might happen if there was a spell of particularly hot weather that causes inspection of the tracks?

Answers: 1

Answer

You know the right answer?

Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220 °C flows in p...

Questions