Engineering, 15.04.2020 20:45 dread0
Consider a large vertical plate with a uniform surface temperature of 100°C suspended in quiescent air at 25°C and atmospheric pressure. (a) Estimate the boundary layer thickness at a location 0.28 m measured from the lower edge. (b) What is the maximum velocity in the boundary layer at this location and at what position in the boundary layer does the maximum occur? (c) Using the similarity solution result, Equation 9.19, determine the heat transfer coefficient 0.25 m from the lower edge. (d) At what location on the plate measured from the lower edge will the boundary layer become turbulent?
Answers: 3
Engineering, 04.07.2019 18:10
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
Engineering, 04.07.2019 18:10
Apipe with an outside diameter of 15 cm is exposed to an ambient air and surrounding temperature of -20°c. the pipe has an outer surface temperature of 65°c and an emissivity of 0.85. if the rate of heat loss from the pipe surface is 0.95 kw per meter of length, the external convective heat transfer coefficient (h) is: (a) 12.5 w/m"k (b) 18.6 w/mk (c) 23.7 w/mk (d) 27.9 w/mk (e) 33.5 w/mk
Answers: 1
Engineering, 04.07.2019 18:20
For each of the following process: a) sketch the p-v diagram, b)sketch t-s diagram, c) sketch t-v diagram, d) sketch the boundary work on one of the diagrams (a, b or c) and e) sketch the reversible heat transfer on one of the diagrams (a, b or c): 1- isobaric process from compressed liquid to superheated vapor 2- isothermal process from compressed liquid to superheated vapor 3- isentropic process from compressed liquid to superheated vapor
Answers: 3
Engineering, 06.07.2019 02:30
On solidification from a melt, the polymer polyethylene forms a semi-crystalline spherulite structure. (i) sketch an individual spherulite and label the amorphous and crystalline regions. (ii) draw a schematic to show the changes in specific volume with temperature during cooling from the melt, comparing it to the theoretical extremes of fully crystalline and fully amorphous (indicate tm and tg)
Answers: 2
Consider a large vertical plate with a uniform surface temperature of 100°C suspended in quiescent a...
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Social Studies, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Chemistry, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01
Mathematics, 11.09.2020 15:01