Engineering, 17.04.2020 16:50 22justinmcminn

The turbocharger of an internal combustion engine consists of a turbine, and a compressor. Hot exhaust gases flow through the turbine to produce work and the work output from the turbine is used as the work input to the compressor. The pressure of ambient air is increased as it flows through the compressor before it enters the engine cylinders. Thus, the purpose of a turbocharger is to increase the pressure of the air so that more air gets into the cylinders. Consequently, more fuel can be burned and more power can be produced by the engine. In a turbocharger, exhaust gases enter the turbine at 400 degrees C and 120kPa at a rate 0.02 kg/s and leaves at 350 degrees C. Air enters the compressor at 50 degrees C and 100kPa and leaves at 130kPa at a rate of 0.018 kg/s. The compressor increases the air pressure with a side effect: It also increases the air temperature, which increases the gasoline engine to experience and engine knock. To avoid this, an aftercooler is placed after the compressor to cool the warm air by cold ambient air before it enters the engine cylinders. It is estimated the aftercooler must decrease the air temperature below 80 degrees C if knock is to be avoided. The cold ambient air enters the aftercooler at 30 degrees C and leaves at 40 degrees C. Disregard any frictional losses in the turbine and the compressor and treating the exhaust gases as air, determine (a) the temperature of the air at the compressor outlet and (b) the minimum volume flow rate of ambient air required to avoid knock.

Answers: 1

Show answers

Answers

Answer from: hunterthompson2

Explanation:

The turbocharger of an internal combustion engine consists of a turbine, and a compressor. Hot exhaust gases flow through the turbine to produce work and the work output from the turbine is used as the work input to the compressor. The pressure of ambient air is increased as it flows through the compressor before it enters the engine cylinders. Thus, the purpose of a turbocharger is to increase the pressure of the air so that more air gets into the cylinders. Consequently, more fuel can be burned and more power can be produced by the engine. In a turbocharger, exhaust gases enter the turbine at 400 degrees C and 120kPa at a rate 0.02 kg/s and leaves at 350 degrees C. Air enters the compressor at 50 degrees C and 100kPa and leaves at 130kPa at a rate of 0.018 kg/s. The compressor increases the air pressure with a side effect: It also increases the air temperature, which increases the gasoline engine to experience and engine knock. To avoid this, an aftercooler is placed after the compressor to cool the warm air by cold ambient air before it enters the engine cylinders. It is estimated the aftercooler must decrease the air temperature below 80 degrees C if knock is to be avoided. The cold ambient air enters the aftercooler at 30 degrees C and leaves at 40 degrees C. Disregard any frictional losses in the turbine and the compressor and treating the exhaust gases as air, determine (a) the temperature of the air at the compressor outlet and (b) the minimum volume flow rate of ambient air required to avoid knock.

Answer from: Quest

answer:

explanation:

sbbdbdbdbdbdndjd

Answer from: Quest

angvrswer:

vfg

grfhrtrhr:

jjj

yjujuju

jujuhuyhyt

bgf

bgr

gbr

bgr

gtr

bgr

gbgbbg

bgg

bbg

bfg

dcwf

fdb

ggb

rfe

gtg

gegte

gff

dfg

gfdsax

cvfbgnh

jmhngf

dsaazxscvb

nmhgb

fvdcsxaz

zxcv

bghn

Another question on Engineering

Engineering, 03.07.2019 14:10

Explain the difference laminar and turbulent flow. explain it with the shear stress and the velocity profiles.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Give heat transfer applications for the following, (i) gas turbines (propulsion) ) gas turbines (power generation). (iii) steam turbines. (iv) combined heat and power (chp). (v) automotive engines

Answers: 1

Answer

Engineering, 04.07.2019 18:10

The higher the astm grain-size number, the coarser the grain is. a)-true b)-false

Answers: 3

Answer

Engineering, 04.07.2019 18:20

Asolid cylinder is concentric with a straight pipe. the cylinder is 0.5 m long and has an outside diameter of 8 cm. the pipe has an inside diameter of 8.5 cm. the annulus between the cylinder ad the pipe contains stationary oil. the oil has a specific gravity of 0.92 and a kinematic viscosity of 5.57 x 10-4 m2/s. most nearly, what is the force needed to move the cylinder along the pipe at a constant velocity of 1 m/s?

Answers: 3

Answer

You know the right answer?

The turbocharger of an internal combustion engine consists of a turbine, and a compressor. Hot exhau...

Questions