Engineering, 21.04.2020 16:42 corbinwilliams

3. Explain the operation of a long channel MOSFET including an explanation of the roleof the gate and drain in causing current ow. Include diagrams of the FET showinghow the depletion and inversion regions change with the applied voltage, and includethe corresponding I-V characteristics. Please read carefully:THIS PROBLEM WILL APPEAR VERBATIM ONTHE FINAL EXAM as a 15 point problem. I will notbe supplying a solutionkey for this particular problem, but would like for you to reach out to me ifyou have questions about answering the problem before the nal examPlease note that the detail for this is contained in my lecture notes, andthe ipped videos. Outline for your answer, and my grading scheme:•10 points: For a xed value ofVgs, explain whyIdschanges shape withVds.{5 points will be allocated for explaining the shape in linear mode{5 points will be allocated for explaining the shape in saturation mode and theassociated "bending" of the curve.{The answer needs to emphasize how the inversion and depletion regions changewith the gate and drain voltages as well as WHY they change for full credit. Just copying gures from the notes still needs an explanation.•5 points: Explain whyIdschanges for each value ofVgs. My hint is to start fromthe expression for drift current. What terms of the drift current would be modi edby a gate voltage, and WHY is this the case?

Answers: 1

Show answers

Another question on Engineering

Engineering, 03.07.2019 15:10

Ahouse has the following electrical appliance usage (1) single 40w lamp used for 4 hours per day (2) single 60w fan used for 12 hours per day (3) single 200w refrigerator that runs 24 hours per day with compressor run 12 hours and off 12 hours find the solar power inverter size in watt with correction factor of 1.25.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the water level in the tank, through a 2.2-cm-internal-diameter pipe by maintaining a constant air pressure of 300 kpa (gage) in the tank. if the head loss in the piping is 2 m of water, determine the discharge rate of the supply of water to the roof top in liters per second.

Answers: 3

Answer

You know the right answer?

3. Explain the operation of a long channel MOSFET including an explanation of the roleof the gate an...

Questions