subject
Engineering, 23.04.2020 01:52 carroch

A three storey structure having a square footprint of 225 m2 is constructed on a clayey deposit. The structure is planned to be supported by square isolated footings having a width of 2m and spaced at 5m center to center. A typical borehole indicates that the soil consists of 2m fill layer at the top (=17KN/m3) followed by a very stiff clay layer 2m thick (sat=18.5KN/m3) underlain by a normally consolidated soft clay layer of 4.5m thickness (sat=17KN/m3) followed by a rock layer extending down to the bottom of borehole. The foundations are laid on top of the stiff clay layer. Water table is located at the top of the stiff clay layer. Undisturbed samples were taken from the middle of each clay layer and consolidation tests done on undisturbed samples indicated the following:

 Stiff Clay: Cc=0.15; Cs = 0.02; Pc = 120 kPa; e0=0.9
 Soft Normally Consolidated Clay: Cc=0.38; Cs = 0.06; e0=1.0

a) Draw a sketch representing the various problem components.

b) The isolated foundations are subjected to a stress of 140 kPa. Calculate the consolidation settlement. Consider the very stiff clay as one layer and divide soft clay layer into two equal sub-layers. Calculate settlement under one typical foundation.

c) What would be the maximum additional stress applied on a central foundation from two neighboring foundations (situated at the left and right sides of the central foundation). Is it necessary to consider the additional stresses from neighboring foundations in the settlement calculations?

d) A concern is the differential settlement between isolated adjacent footings. It was decided to change the design to have the structure founded on a raft foundation subjected to a stress of 45 kPa. Compute the consolidation settlement and comment on the results.

ansver
Answers: 3

Another question on Engineering

question
Engineering, 04.07.2019 18:10
Refrigerant 134a enters an insulated compressor operating at steady state as saturated vapor at -26°c with a volumetric flow rate of 0.18 m3/s. refrigerant exits at 9 bar, 70°c. changes in kinetic and potential energy from inlet to exit can be ignored. determine the volumetric flow rate at the exit, in m3/s, and the compressor power, in kw.
Answers: 1
question
Engineering, 04.07.2019 18:20
Aquick transition of the operating speed of a shaft from its critical speed will whirl amplitude. (a) increase (b) limit (c) not affect (d) zero
Answers: 2
question
Engineering, 04.07.2019 19:10
Air inially occupying a volume of 1 m2 at 100 kpa, 27 c undergoes three internally reversible processes in series. process 1-2 compression to 500 kpa during which pv constant process 2-3 adiabatic expanslon to 100 kpa process 3-1: constant-pressure expansion to 100 kpa (a) calculate the change of entropy for each of the three processes. (b) calculate the heat and work involved in each process. (c) is this cycle a power cycle or refrigeration cycle?
Answers: 3
question
Engineering, 04.07.2019 19:10
Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.
Answers: 2
You know the right answer?
A three storey structure having a square footprint of 225 m2 is constructed on a clayey deposit. The...
Questions
question
Physics, 16.10.2020 06:01
question
Chemistry, 16.10.2020 06:01
question
World Languages, 16.10.2020 06:01
question
Mathematics, 16.10.2020 06:01
question
Mathematics, 16.10.2020 06:01
question
Mathematics, 16.10.2020 06:01
question
Mathematics, 16.10.2020 06:01
question
Mathematics, 16.10.2020 06:01
Questions on the website: 13722367