![subject](/tpl/images/cats/User.png)
Engineering, 25.04.2020 05:01 igobeastmode
Asolid rectangular rodhas a length of 90mm, made of steel material (E =207,000 MPa, Syield= 300 MPa), the cross section of the rod is shownbelow. If the boundary conditions are fixed-freeand a safety factor of 2 on loadis required, (1)Find themaximumallowable load (Pallowable)on the rod. [9points]{hint: Pallowable= Pcr/required safety factor}(2)If the same critical load (Pcr) calculated from (1)above(Pcrisalready taken into accounta safety factor of 2)is applied to a solid round rodunderthe same boundary conditions, what is the minimum required diameter of the rod against buckling? [9points]
![ansver](/tpl/images/cats/User.png)
Answers: 3
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
The flow rate of air through a through a pipe is 0.02 m5/s. a pitot static tube is placed in the flow. the radius of the pitot static tube is 1 mm. assuming the flow to be steady and the air to be at 300k, calculate the difference in total and static pressure if the diameter of the pipe is: (a) d 0.1 m d 0.05 m (c) d 0.01 m
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Derive the correction factor formula for conical nozzle i=-(1+ cosa) and calculate the nozzle angle correction factor for a nozzle whose divergence hal-fangle is 13 (hint: assume that all the mass flow originates at the apex of the cone.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
With increases in magnification, which of the following occur? a. the field of view decreases. b. the ambient illumination decreases. c. the larger parts can be measured. d. the eyepiece must be raised.
Answers: 1
You know the right answer?
Asolid rectangular rodhas a length of 90mm, made of steel material (E =207,000 MPa, Syield= 300 MPa)...
Questions
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 25.06.2021 05:00
![question](/tpl/images/cats/en.png)
English, 25.06.2021 05:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/fizika.png)
Physics, 25.06.2021 05:00
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 25.06.2021 05:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 25.06.2021 05:10
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 25.06.2021 05:10