Engineering, 02.06.2020 17:58 joel4676
The purpose of this assignment is to analyze the internal convection case of a flow through a round pipe to understand the heat transfer between the water flowing through the tubes of the cooling water circuit. In particular, you will be exploring the effects of flow rate, tube diameter, and tube length for fully developed conditions.
For the following conceptual questions, consider the flow to always be turbulent.
If the tube length and diameter remain constant, state the effect of increasing the flow rate on each of the following:
Reá´ increase no effect decrease cannot determine
Nμᴠincrease no effect decrease cannot determine
h increase no effect decrease cannot determine
|T_m, out - T_m, in| increase no effect decrease cannot determine
Îp increase no effect decrease cannot determine
If the flow rate and tube length remain constant, state the effect of increasing tube diameter on each of the following:
Reá´ increase no effect decrease cannot determine
Nμᴠincrease no effect decrease cannot determine
h increase no effect decrease cannot determine
|T_m, out - T_m, in| increase no effect decrease cannot determine
Îp increase no effect decrease cannot determine
If the flow rate and tube diameter remain constant, state the effect of increasing tube length on each of the following:
Reá´ increase no effect decrease cannot determine
Nμᴠincrease no effect decrease cannot determine
h increase no effect decrease cannot determine
|T_m, out - T_m, in| increase no effect decrease cannot determine
Îp increase no effect decrease cannot determine
For an assumed internal tube diameter of D = 0.375 inches and length of L = 20 feet, consider volumetric flow rates in the range of 0 < Å¥ â¤10 gallons/minute. For this range of flow rates, create two plots associated with the convective heat transfer: Nup vs Re, and also h vs R. Then, assuming a uniform surface temperature of 38°F and a water inlet temperature of 32°F, compute and plot the rate of heat transfer (in W) for 0 < Å¥ ⤠10 gpm.
Answers: 2
Engineering, 04.07.2019 18:10
The mass flow rate of the fluid remains constant in all steady flow process. a)- true b)- false
Answers: 1
Engineering, 04.07.2019 18:10
Abrake has a normal braking torque of 2.8 kip in and heat-dissipating cast-iron surfaces whose mass is 40 lbm. suppose a load is brought to rest in 8.0 s from an initial angular speed of 1600 rev/min using the normal braking torque; estimate the temperature rise of the heat dissipating surfaces.
Answers: 3
Engineering, 04.07.2019 18:10
Which of the following components of a pid controlled accumulates the error over time and responds to system error after the error has been accumulated? a)- proportional b)- derivative c)- integral d)- on/off.
Answers: 2
Engineering, 04.07.2019 18:10
Water at the rate of 1 kg/s is forced through a tube with a 2.5 cm inner diameter. the inlet water temperature is 15°c, and the outlet water temperature is 50°c. the tube wall temperature is 14°c higher than the local water temperature all along the length of the tube. what is the length of the tube?
Answers: 3
The purpose of this assignment is to analyze the internal convection case of a flow through a round...
Chemistry, 29.05.2020 08:00
Mathematics, 29.05.2020 08:00
Mathematics, 29.05.2020 08:00
English, 29.05.2020 08:00
Physics, 29.05.2020 08:00
Chemistry, 29.05.2020 08:00
Computers and Technology, 29.05.2020 08:00
Mathematics, 29.05.2020 08:00
Mathematics, 29.05.2020 08:00
Physics, 29.05.2020 08:00
Physics, 29.05.2020 08:00
Mathematics, 29.05.2020 08:00