![subject](/tpl/images/cats/User.png)
Engineering, 18.06.2020 22:57 abelsoto
Design a rod that will have an interference fit so that the allowance (the
maximum interference) is 0.010 with the center hole in the Rocker Arm
and the tolerance on the rod diameter is .002. Sketch a section view of
your rod design. Be sure to specify the tolerance in the diameter
dimension of your design.
![ansver](/tpl/images/cats/User.png)
Answers: 1
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
An air conditioning system consist of a 5 cm diameter pipe, operating at a pressure of 200 kpa. the air initially enters the pipe at 15°c with a velocity of 20 m/s and relative humidity of 80%. if the heat supply throughout the process is 960 w, determine the relative humidity and the temperature at the outlet
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Select any two (2) areas of applications of chain-drive. (clo4) a)-permanent lubrication necessary b)-hydraulic forklift truck operation c)-rigging and heavy moving materials d)-relatively high maintenance costs e)-costlier than belt drives
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Aquick transition of the operating speed of a shaft from its critical speed will whirl amplitude. (a) increase (b) limit (c) not affect (d) zero
Answers: 2
You know the right answer?
Design a rod that will have an interference fit so that the allowance (the
maximum interference) is...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 06:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 05.01.2020 06:31
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 06:31
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 06:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 06:31
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 06:31
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 06:31
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 06:31
![question](/tpl/images/cats/health.png)
Health, 05.01.2020 06:31
![question](/tpl/images/cats/mat.png)
Mathematics, 05.01.2020 06:31