Engineering, 01.07.2020 22:01 peachyparty

A 50 Hz, four pole turbo-generator rated 100 MVA, 11 kV has an inertia constant of 8.0 MJ/MVA. (a) Find the stored energy in the rotor at synchronous speed. (b) If the mechanical input is suddenly raised to 80 MW for an electrical load of 50 MW, find rotor acceleration, neglecting mechanical and electrical losses. (c) If the acceleration calculated in part(b) is maintained for 10 cycles, find the change in torque angle and rotor speed in revolutions per minute at the end of this period.

Answers: 2

Show answers

Answers

Answer from: stephaniero6

Given Information:

Frequency = f = 60 Hz

Complex rated power = G = 100 MVA

Intertia constant = H = 8 MJ/MVA

Mechanical power = Pmech = 80 MW

Electrical power = Pelec = 50 MW

Number of poles = P = 4

No. of cycles = 10

Required Information:

(a) stored energy = ?

(b) rotor acceleration = ?

(a) stored energy = 800 Mj

(b) rotor acceleration = 337.46 elec deg/s²

Explanation:

(a) Find the stored energy in the rotor at synchronous speed.

The stored energy is given by

$E = G \times H$

Where G represents complex rated power and H is the inertia constant of turbo-generator.

$E = 100 \times 8 \\\\E = 800 \: MJ$

(b) If the mechanical input is suddenly raised to 80 MW for an electrical load of 50 MW, find rotor acceleration, neglecting mechanical and electrical losses.

The rotor acceleration is given by

$P_a = P_{mech} - P_{elec} = M \frac{d^2 \delta}{dt^2}$

Where M is given by

$M = \frac{E}{180 \times f}$

$M = \frac{800}{180 \times 50}$

$M = 0.0889 \: MJ \cdot s/ elec \: \: deg$

So, the rotor acceleration is

$P_a = 80 - 50 = 0.0889 \frac{d^2 \delta}{dt^2}$

$30 = 0.0889 \frac{d^2 \delta}{dt^2}$

$\frac{d^2 \delta}{dt^2} = \frac{30}{0.0889}$

$\frac{d^2 \delta}{dt^2} = 337.46 \:\: elec \: deg/s^2$

(c) If the acceleration calculated in part(b) is maintained for 10 cycles, find the change in torque angle and rotor speed in revolutions per minute at the end of this period.

The change in torque angle is given by

$\Delta \delta = \frac{1}{2} \cdot \frac{d^2 \delta}{dt^2}\cdot (t)^2$

Where t is given by

$1 \: cycle = 1/f = 1/50 \\\\10 \: cycles = 10/50 = 0.2 \\\\t = 0.2 \: sec$

So,

$\Delta \delta = \frac{1}{2} \cdot 337.46 \cdot (0.2)^2$

$$ \Delta \delta = 6.75 \: elec \: deg$

The change in torque in rpm/s is given by

$\Delta \delta = \frac{337.46 \cdot 60}{2 \cdot 360\circ }$

$\Delta \delta =28.12 \: \: rpm/s$

The rotor speed in revolutions per minute at the end of this period (10 cycles) is given by

$Rotor \: speed = \frac{120 \cdot f}{P} + (\Delta \delta)\cdot t$

Where P is the number of poles of the turbo-generator.

$Rotor \: speed = \frac{120 \cdot 50}{4} + (28.12)\cdot 0.2$

$Rotor \: speed = 1500 + 5.62$

$$ Rotor \: speed = 1505.62 \:\: rpm$

Answer from: Quest

answer:

science is the study of the nature and behavior of natural things and the knowledge that we obtain about them. a science is a particular branch of science such as physics, chemistry, or biology. physics is the best example of a science which has developed strong, abstract theories.

pseudoscience is a collection of beliefs or practices mistakenly regarded as being based on scientific method.

plz rate as brainliest

Answer from: Quest

El presidente del gobierno mariano y el presidente

Another question on Engineering

Engineering, 04.07.2019 18:10

Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the water level in the tank, through a 2.2-cm-internal-diameter pipe by maintaining a constant air pressure of 300 kpa (gage) in the tank. if the head loss in the piping is 2 m of water, determine the discharge rate of the supply of water to the roof top in liters per second.

Answers: 3

Answer

Engineering, 06.07.2019 03:30

An ammonia compressor has a 5% clearance volume and displacement rate of 80 l/s and pumps against a condensing temperature of 40°c. for two different temperatures of -10°c and 10°c, compute the mass flow rate of refrigerant assuming the clearance volumetric efficiency applies. discharge specific volume corresponding to-10°c and 10°c are 112.5 l/kg and 95 l/kg, respectively.

Answers: 2

Answer

Engineering, 06.07.2019 04:30

At flow nozzle is to be installedin a 5-in type k copper tube carrying linseed oil at 77 f. a mercury manometer is to be used to measure the pressure difference across the nozzle when the expected range of the flow rate is from 700 galmin to 1000 gal/min. the manometer scale ranges from 0 to 8.0 in of mercury determine an appropriate diameter of the nozzle.

Answers: 2

Answer

Engineering, 11.07.2019 00:40

Areversible power cycle operates with a thermal efficiency of 75%. the cycle receives energy input by heat from a thermal reservoir at 1200k. what is the temperature, in k, of the low temperature thermal reservoir?

Answers: 2

Answer

You know the right answer?

A 50 Hz, four pole turbo-generator rated 100 MVA, 11 kV has an inertia constant of 8.0 MJ/MVA. (a) F...

Questions