Engineering, 17.07.2020 16:01 rashawnglover

An inverted tee lintel is made of two 8" x 1/2" steel plates. Calculate the maximum bending stress in tension and compression when the lintel carries a total uniformly distributed load of 10000 lb on a simple span of 6 ft. Also, calculate the average shear stress at the neutral axis and the average shear stresses at the web and the flange

Answers: 1

Show answers

Answers

Answer from: qwertylol12345

hello your question lacks some information attached is the complete question

A) (i)maximum bending stress in tension = 0.287 * 10^6 Ib-in

(ii) maximum bending stress in compression = 0.7413*10^6 Ib-in

B) (i) The average shear stress at the neutral axis = 0.7904 *10 ^5 psi

(ii) Average shear stress at the web = 18.289 * 10^5 psi

(iii) Average shear stress at the Flange = 1.143 *10^5 psi

Explanation:

First we calculate the centroid of the section,then we calculate the moment of inertia and maximum moment of the beam( find attached the calculation)

A) Calculate the maximum bending stress in tension and compression

lintel load = 10000 Ib

simple span = 6 ft

( (moment of inertia*Y)/ I ) = MAXIMUM BENDING STRESS

I = 53.54

i) The maximum bending stress (fb) in tension=

= $\frac{M_{mm}Y }{I}$ = $\frac{6.48 * 10^6 * 2.375}{53.54}$ = 0.287 * 10^6 Ib-in

ii) The maximum bending stress (fb) in compression

= $\frac{M_{mm}Y }{I}$ = $\frac{6.48 *10^6*(8.5-2.375)}{53.54}$ = 0.7413*10^6 Ib-in

B) calculate the average shear stress at the neutral axis and the average shear stresses at the web and the flange

i) The average shear stress at the neutral axis

V = $\frac{wL}{2}$ = $\frac{1000*6*12}{2}$ = 3.6*10^5 Ib

Ay = 8 * 0.5 * (2.375 - 0.5 ) + 0.5 * (2.375 - $\frac{0.5}{2}$ ) * $\frac{(2.375 - (\frac{0.5}{2} ))}{2}$

= 5.878 in^3

t = VQ / Ib = ( 3.6*10^5 * 5.878 ) / (53.54 8 0.5) = 0.7904 *10 ^5 psi

ii) Average shear stress at the web ( value gotten from the shear stress at the flange )

t = 1.143 * 10^5 * (8 / 0.5 ) psi

= 18.289 * 10^5 psi

iii) Average shear stress at the Flange

t = VQ / Ib = $\frac{3.6*10^5 * 8*0.5*(2.375*(0.5/2))}{53.54 *0.5}$

= 1.143 *10^5

An inverted tee lintel is made of two 8 x 1/2 steel plates. Calculate the maximum bending stress i

Answer from: Quest

explanation:

i don't understand really? can u provide more information

u should make a machine that can make ice cream fresh!

Answer from: Quest

answer:

explanation:

assault rifle is a rapid-fire, magazine-fed rifle designed for military use. it is a shoulder-fired weapon that allows the shooter to select between semi-automatic (requiring you pull the trigger for each shot), fully automatic (hold the trigger and the gun continuously fires) or three-shot-burst modes.

Another question on Engineering

Engineering, 03.07.2019 15:10

Heat is added to a piston-cylinder device filled with 2 kg of air to raise its temperature 400 c from an initial temperature of t1 27 cand pressure of pi 1 mpa. the process is isobaric process. find a)-the final pressure p2 b)-the heat transfer to the air.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Shafts are machine elements that are used to a) carry axial loads b) direct shear loads c) transmit power d) rotate at constant speed e) none of the above circular and square shafts subjected to the same torque under the same circum behave a) the same way b) almost the same way

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Asimple rankine cycle uses water as the working fluid. the water enters the turbine at 10 mpa and 480c while the condenser operates at 6 kpa. if the turbine has an isentropic efficiency of 80 percent while the pump has an isentropic efficiency of 70 percent determine the thermal efficiency

Answers: 1

Answer

Engineering, 05.07.2019 19:10

Tech a says never use a water hose to clean up dust after a repair. tech b says never use a floor scrubber to clean up dust after repairs. who is correct?

Answers: 1

Answer

You know the right answer?

An inverted tee lintel is made of two 8" x 1/2" steel plates. Calculate the maximum bending stress i...

Questions