top-down design
![subject](/tpl/images/cats/User.png)
Engineering, 28.07.2020 07:01 melo2424
Which type of engineering design uses an already-existing design?
A.
top-down design
B.
spiral design
C.
bottom-up design
D.
incremental design
![ansver](/tpl/images/cats/User.png)
Answers: 2
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Manometers are good examples of measuring instruments, nowadays they are not as common as before. a)-capacitive probe gauges b)-gravitational gauges deformation ) gauges d)-digital gauges
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200°c and outer surface temperature of the insulation to be 15°c. calculate the thickness of insulation required.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
Agas contained within a piston-cylinder assembly e end nation about same energy states, 1 and 2, where pi 10 bar, v undergoes two processes, a and b, between the sam 0.1 m3, ui-400 kj and p2 1 bar, v2 1.0 m2, u2 200 kj: process a: process from 1 to 2 during which the pressure- volume relation is pv constant process b: constant-volume process from state 1 to a pressure of 2 bar, followed by a linear pressure-volume process to +20 0 state 2 kinetic and potential energy effects can be ignored. for each of the processes a and b, (a) sketch the process on p-v coordinates, (b) evaluate the work, in kj, and (c) evaluate process the heat transfer, in kj
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20
At steady state, air at 200 kpa, 325 k, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. the inlet cross-sectional area is 6 cm2. at the duct exit, the pressure of the air is 100 kpa and the velocity is 250 m/s. neglecting potential energy effects and modeling air as an 1.008 kj/kg k, determine ideal gas with constant cp = (a) the velocity of the air at the inlet, in m/s. (b) the temperature of the air at the exit, in k. (c) the exit cross-sectional area, in cm2
Answers: 2
You know the right answer?
Which type of engineering design uses an already-existing design?
A.
top-down design
top-down design
Questions
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
Health, 14.02.2020 11:51
![question](/tpl/images/cats/es.png)
Spanish, 14.02.2020 11:51
![question](/tpl/images/cats/en.png)
English, 14.02.2020 11:52
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 14.02.2020 11:54
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 14.02.2020 11:54
![question](/tpl/images/cats/istoriya.png)
History, 14.02.2020 12:03
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 14.02.2020 12:07
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
English, 14.02.2020 12:08
![question](/tpl/images/cats/health.png)
Health, 14.02.2020 12:08
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 14.02.2020 12:08
![question](/tpl/images/cats/en.png)
English, 14.02.2020 12:10
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 14.02.2020 12:10