![subject](/tpl/images/cats/User.png)
Engineering, 12.08.2020 18:01 cjs39
A large piece of ground is developed with lights, streets, and sewers. The subdivider wants to get it ready for building. He does an environmental impact statement and makes a large map which shows where each lot and block is located. Streets, parks, and utility easement are also shown. This is visual representation is called:
![ansver](/tpl/images/cats/User.png)
Answers: 1
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 16:10
The force on a cutting tool are 2600n vertically downward and 2100 horizontal. determine the resultant force acting on the tool and the angle at which it acts.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Determine whether or not it is possible to compress air adiabatically from k to 140 kpa and 400 k. what is the entropy change during this process?
Answers: 3
You know the right answer?
A large piece of ground is developed with lights, streets, and sewers. The subdivider wants to get i...
Questions
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 28.09.2019 00:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 28.09.2019 00:00
![question](/tpl/images/cats/mat.png)
Mathematics, 28.09.2019 00:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 28.09.2019 00:00
![question](/tpl/images/cats/istoriya.png)
History, 28.09.2019 00:00
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/fizika.png)
Physics, 28.09.2019 00:00
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 28.09.2019 00:00
![question](/tpl/images/cats/biologiya.png)