subject
Engineering, 30.11.2020 17:40 emmanuelmashao6704

Brainiest and 35 points for the RIGHT ANSWER Which of the following devices is used to determine if an item is horizontal?

a level
a lever
a shank
a clamp

ansver
Answers: 2

Another question on Engineering

question
Engineering, 03.07.2019 15:10
Two flowing streams of argon gas are adiabatically mixed to form a single flow/stream. one stream is 1.5 kg/s at 400 kpa and 200 c while the second stream is 2kg/s at 500 kpa and 100 ? . it is stated that the exit state of the mixed single flow of argon gas is 150 c and 300 kpa. assuming there is no work output or input during the mixing process, does this process violate either the first or the second law or both? explain and state all your assumptions.
Answers: 1
question
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
question
Engineering, 04.07.2019 18:10
Which of the following components of a pid controlled accumulates the error over time and responds to system error after the error has been accumulated? a)- proportional b)- derivative c)- integral d)- on/off.
Answers: 2
question
Engineering, 04.07.2019 19:10
Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.
Answers: 2
You know the right answer?
Brainiest and 35 points for the RIGHT ANSWER Which of the following devices is used to determine if...
Questions
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Social Studies, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
question
Business, 16.09.2020 01:01
question
Mathematics, 16.09.2020 01:01
Questions on the website: 13722362