![subject](/tpl/images/cats/User.png)
Engineering, 14.01.2021 20:00 altamiranojosue7
Which of the following geometric shapes allow a design to be viewed in a three-dimensional format?
prisms and squares
cubes and prisms
circles and squares
spheres and triangles
![ansver](/tpl/images/cats/User.png)
Answers: 3
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 12:10
On a average work day more than work place firs are reorted
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
Agas contained within a piston-cylinder assembly e end nation about same energy states, 1 and 2, where pi 10 bar, v undergoes two processes, a and b, between the sam 0.1 m3, ui-400 kj and p2 1 bar, v2 1.0 m2, u2 200 kj: process a: process from 1 to 2 during which the pressure- volume relation is pv constant process b: constant-volume process from state 1 to a pressure of 2 bar, followed by a linear pressure-volume process to +20 0 state 2 kinetic and potential energy effects can be ignored. for each of the processes a and b, (a) sketch the process on p-v coordinates, (b) evaluate the work, in kj, and (c) evaluate process the heat transfer, in kj
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20
Acommercial grade cubical freezer, 4 m on a side, has a composite wall consisting of an exterior sheet of 5.0-mm thick plain carbon steel (kst= 60.5 w/m k), an intermediate layer of 100-mm thick polyurethane insulation (kins 0.02 w/m k), and an inner sheet of 5.0- mm thick aluminium alloy (kal polyurethane insulation and both metallic sheets are each characterized by a thermal contact resistance of r 2.5 x 104 m2 k/w. (a) what is the steady-state cooling load that must be maintained by the refrigerator under conditions for which the outer and inner surface temperatures are 25°c and -5°c, respectively? (b) for power saving purpose, which wall material should be increased/reduced in. thickness in order to reduce 50% of the cooling load found in part (a)? redesign the thickness of the proposed material. 177 w/m-k). adhesive interfaces between the q=575.93 w
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 03:20
Avertical steel rod of length 2.0 m and diameter 25 mm is rigidly fixed at its upper end and has a flange at its lower, free, end. what will be the maximum stress produced in the rod when a load of 20 kn is applied, (a) gradually to the lower end, (b) suddenly to the lower end, (c) by a collar falling from a height of 50 mm on to the flange?
Answers: 3
You know the right answer?
Which of the following geometric shapes allow a design to be viewed in a three-dimensional format?...
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 15.10.2019 23:30
![question](/tpl/images/cats/istoriya.png)
History, 15.10.2019 23:30
![question](/tpl/images/cats/geografiya.png)
Geography, 15.10.2019 23:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 15.10.2019 23:30
![question](/tpl/images/cats/istoriya.png)
History, 15.10.2019 23:30
![question](/tpl/images/cats/mir.png)
![question](/tpl/images/cats/en.png)
English, 15.10.2019 23:30
![question](/tpl/images/cats/himiya.png)
Chemistry, 15.10.2019 23:30
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 15.10.2019 23:30
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
Health, 15.10.2019 23:30
![question](/tpl/images/cats/en.png)
English, 15.10.2019 23:30
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/istoriya.png)
History, 15.10.2019 23:30