subject
Engineering, 23.02.2021 19:00 rosehayden21

On a separate sheet of paper practice drawing a 10ft. Vertical line at three different scales using American system: ½” = 1’;
½”=1’;
⅛”=1’

Draw also 12m. Vertical line at three different scales using the Metric System:
4) 1/50 CM;
5) 1/100 CM;
6) 1/200 CM;

7] A street on a block plan is drawn at a scale of 1”= 50’. When the drawing is measured with a ruler, the street is ½” wide. How wide is the actual street? Explain


8] A street on a block plan is drawn at a scale of 1”= 10’. When the drawing is measured with a ruler, the street is 5” wide. How wide is the actual street? Explain


9] In your own words describe the three types of scale.
Answer here:

En una hoja de papel separada, practique el dibujo de una linea vertical de 10 pies a tres escalas diferentes utilizando Sistema Americano:
½ “= 1’;
½ “= 1’;
⅛ “= 1’

Dibuja tamben una linea vertical de 12m. A tres escalas diferentes untilizando el Sistema Metrico:
4) 1/50 CM;
5) 1/100 CM;
6) 1/200 CM;

7] Una calle en un plano de bloque se dibuja a una escala de 1 "= 50 '. Cuando el dibujo se mide con una regla, la calle tiene ½ ”de ancho.
¿Qué anchura real tiene la calle? Explique

8] Una calle en un plano de bloque se dibuja a una escala de 1 ”= 10 '. Cuando el dibujo se mide con una regla, la calle tiene 5 ”de ancho.
¿Qué anchura real tiene la calle? Explique

9] En sus palabras describe las tres tipos de escala.

Escribe aqui:

ansver
Answers: 1

Another question on Engineering

question
Engineering, 04.07.2019 19:20
The power source in a certain welding setup generates 3500w that is transferred to the low carbon steel work with a heat transfer factor of 0.85. the melting factor in the operation is 0.45. a continuous fillet weld is to be made with a cross-sectional area of 23 mm2 determine the travel speed at which the welding can be accomplished.
Answers: 3
question
Engineering, 04.07.2019 19:20
Apiping systems consists of 6 m of 6-std type k and 12 m of 4-std type k, both drawn copper tubing. the system conveys ethylene glycol at a rate of 0.013 m3/s. the pressure drop across the system is to be calculated. there are two 90° elbows in the 6-in pipe, a reduction from the 6-in pipe to the 4-in pipe and four 90° elbows in the 4-in pipe. all fittings are soldered (same as flanged) and regular. the inlet and outlet of the system are at the same height.
Answers: 1
question
Engineering, 05.07.2019 23:20
Which one of the following faults cause the coffee in a brewer to keep boiling after the brewing cycle is finished? a. an open circuit in the heating element b. a short circuit at the terminals c. welded contacts on the thermostat d. a leak around the gasket
Answers: 3
question
Engineering, 06.07.2019 02:30
A12 mm diameter shaft runs in a plain cylindrical bush 30 mm long that is located in an 18 mm diameter hole in a housing. the shaft-inner bush fit is h8 f and the outer bush-housing fit is h7-p6. make a fully cimensioned sketch of the bush with tolerances. find the maximum and minimum clearance or interference for both fits on the inner and outer diameters of the bush
Answers: 3
You know the right answer?
On a separate sheet of paper practice drawing a 10ft. Vertical line at three different scales using...
Questions
question
Mathematics, 17.10.2019 08:50
question
Mathematics, 17.10.2019 08:50
question
English, 17.10.2019 08:50
Questions on the website: 13722363