Engineering, 28.02.2021 08:20 makayyafreeman

What is a “V speed”? Why are “V speeds” important? Ans:
Describe the ALTIMETER. How does it work and what does it measure? What is the Kohlsman window? Why must we regularly adjust the Kohlsman setting?
Ans:
1Describe the effects of “non-standard” atmospheric temperature on altimeter accuracy.
Ans:
What is pressure altitude?
Ans:
What is density altitude?
Ans:
What does the vertical speed indicator (VSI) tell us?
Ans:
What does the VSI measure?
Ans:
What is an IVSI? What makes it different from a basic VSI and WHY do we use them on high altitude aircraft?
Ans:
What is a GYROSCOPE? What property does a gyroscope demonstrate while spinning that makes it useful to us?
Ans:
That is gyroscopic precession? How does it act on a spinning mass?
Ans:
Describe an attitude indicator. What does it tell us? Does it indicate whether or not we are TURNING (be careful here)?
Ans:
Describe the TURN COORDINATOR. What does it tell us? What is a “standard rate turn”?
Ans:
Describe the typical aircraft magnetic compass. What does it indicate?
Ans:
What inherent errors are associated with the magnetic compass in an aircraft?
Ans:

Answers: 3

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.

Answers: 3

Answer

Engineering, 04.07.2019 18:20

Along 8-cm diameter steam pipe whose external surface temperature is 900c connects two buildings. the pipe is exposed to ambient air at 70c with a wind speed of 50 km/hr blowing across the pipe. determine the heat loss from the pipe per unit length. (b) air at 500c enters a section of a rectangular duct (15 cm x 20 cm) at an average velocity of 7 m/s. if the walls of the duct are maintained at 100c. a) the length of the tube for an exit temperature of the air to be 40 0c. b)the rate of heat transfer from the air. c) the fan power needed to overcome the pressure drop in this section of the duct.

Answers: 1

Answer

Engineering, 06.07.2019 04:10

Aheat pump using refrigerant-134a heats a house by using underground water at 8°c as the heat source. the house is losing heat at a rate of 60,000 kj/h. the refrigerant enters the compressor at 280 kpa and 0°c, and it leaves at 1 mpa and 60°c. the refrigerant exits the condenser at 30°c. determine: (a) the power input to the heat pump, (b) the rate of heat absorption from the water, and (c) the increase in electric power input if an electric resistance heater is used instead of a heat pump

Answers: 2

Answer

Engineering, 06.07.2019 04:20

Consider the transfer function for a first-order system g(s)=12(s+7)/(s^2+2s+9) for this system determine: a) poles and zeros of the function, b) the natural frequency and damping ratio, c) the peak value achieved in response to a unit step input, d) the peak time for a unit step input, e) the steady-state system response to a unit step input

Answers: 2

Answer

You know the right answer?

What is a “V speed”? Why are “V speeds” important? Ans:
Describe the ALTIMETER. How does it w...

Questions