![subject](/tpl/images/cats/User.png)
Engineering, 21.04.2021 01:40 lopez5628
You are performing a machining operation that approximates orthogonal cutting. Given that the chip thickness prior to chip formation is 0.5 inches and the chip thickness after separation is 1.125 inches, calculate the shear plane angle and shear strain. Use a rake angle of 10 degrees. 21. Suppose in the prior problem that the cutting force and thrust force were measured as 1559 N and 1271 N, respectively. The width of the cut is 3.0mm. Using this new information, calculate the shear strength of the material.
![ansver](/tpl/images/cats/User.png)
Answers: 3
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 14:10
Amass of 1.5 kg of air at 120 kpa and 24°c is contained in a gas-tight, frictionless piston-cylinder device. the air is now compressed to a final pressure of 720 kpa. during the process, heat is transferred from the air such that the temperature inside the cylinder remains constant. calculate the boundary work input during this process.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Modern high speed trains do not have perpendicular expansion gaps where rails are joined end-to-end any more they are mostly welded together but what might happen if there was a spell of particularly hot weather that causes inspection of the tracks?
Answers: 1
You know the right answer?
You are performing a machining operation that approximates orthogonal cutting. Given that the chip t...
Questions
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 11.02.2021 19:50
![question](/tpl/images/cats/mat.png)
Mathematics, 11.02.2021 19:50
![question](/tpl/images/cats/mat.png)
Mathematics, 11.02.2021 19:50
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 11.02.2021 19:50
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/en.png)
English, 11.02.2021 19:50
![question](/tpl/images/cats/mat.png)
Mathematics, 11.02.2021 19:50
![question](/tpl/images/cats/ekonomika.png)
Business, 11.02.2021 19:50
![question](/tpl/images/cats/ap.png)
Advanced Placement (AP), 11.02.2021 19:50
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 11.02.2021 19:50
![question](/tpl/images/cats/geografiya.png)
Geography, 11.02.2021 19:50
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 11.02.2021 19:50
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 11.02.2021 19:50
![question](/tpl/images/cats/mkx.png)
Arts, 11.02.2021 19:50