Can you do this with matlab?
...
![ansver](/tpl/images/cats/User.png)
Answers: 2
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 16:10
The force on a cutting tool are 2600n vertically downward and 2100 horizontal. determine the resultant force acting on the tool and the angle at which it acts.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Steel is coated with a thin layer of ceramic to protect against corrosion. what do you expect to happen to the coating when the temperature of the steel is increased significantly? explain.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
You know the right answer?
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 09.06.2020 07:57
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 09.06.2020 07:57
![question](/tpl/images/cats/himiya.png)
Chemistry, 09.06.2020 07:57
![question](/tpl/images/cats/en.png)
English, 09.06.2020 07:57
![question](/tpl/images/cats/es.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 09.06.2020 07:57
![question](/tpl/images/cats/en.png)
English, 09.06.2020 07:57
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 09.06.2020 07:57
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 09.06.2020 07:57
![question](/tpl/images/cats/mat.png)
Mathematics, 09.06.2020 07:57
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 09.06.2020 07:57
![question](/tpl/images/cats/biologiya.png)
Biology, 09.06.2020 07:57
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 09.06.2020 07:57
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)