![subject](/tpl/images/cats/User.png)
Engineering, 10.06.2021 08:50 barnhill4755
Cantilever beam in the figure is loaded with force F. After that with help of strain gauges 1 and 2, unit elongations were measured (gauge 1 is at the top of the beam with 45 degree to the beam axis and gauge 2 is located at left side at z=0, see top view to ensure. ) Calculate the force F and length with given material properties and gauge lengths.** Note that length of the beam is not important to solve this question** GİVEN: E=2.10^7 N/cm^2,d=10cm, G=8.10^6 N/cm^2,a=45 cm,ε1=385.15x10^-6,ε2=240.10x10^-6
![ansver](/tpl/images/cats/User.png)
Answers: 3
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 14:10
If the thermal strain developed in polyimide film during deposition is given as 0.0044. assume room temperature is kept at 17.3 c, and thermal coefficient of expansion for the film and the substrate are 54 x 10^-6c^-1 and 3.3 x 10^-6c^-1respectively. calculate the deposition temperature.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 19:30
When using the ohmmeter function of a digital multimeter, the leads are placed in what position relative to the component being tested? a. parallel b. control c. series d. line
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Acompressor receives the shaft work to decrease the pressure of the fluid. a)- true b)- false
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater
Answers: 3
You know the right answer?
Cantilever beam in the figure is loaded with force F. After that with help of strain gauges 1 and 2,...
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
Health, 04.12.2020 20:50
![question](/tpl/images/cats/mat.png)
Mathematics, 04.12.2020 20:50
![question](/tpl/images/cats/mat.png)
Mathematics, 04.12.2020 20:50
![question](/tpl/images/cats/mat.png)
Mathematics, 04.12.2020 20:50
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 04.12.2020 20:50
![question](/tpl/images/cats/himiya.png)
Chemistry, 04.12.2020 20:50
![question](/tpl/images/cats/mat.png)
Mathematics, 04.12.2020 20:50
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.12.2020 20:50
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.12.2020 20:50
![question](/tpl/images/cats/mat.png)
Mathematics, 04.12.2020 20:50
![question](/tpl/images/cats/mat.png)
Mathematics, 04.12.2020 20:50