![subject](/tpl/images/cats/User.png)
Engineering, 07.07.2021 20:10 hana560
Questions What is the necessary preparations expected to be done on the surface of a ferrous metal work piece before marking out could be done on it and why? ANSWER:
![ansver](/tpl/images/cats/User.png)
Answers: 2
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Items are similar to the free issue items, but their access is limited. (clo5) a)-bin stock items free issue b)-bin stock controlled issue c)-critical or insurance spares d)-rebuildable spares e)-consumables
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Steam enters a converging nozzle at 3.0 mpa and 500°c with a at 1.8 mpa. for a nozzle exit area of 32 cm2, determine the exit velocity, mass flow rate, and exit mach number if the nozzle: negligible velocity, and it exits (a) is isentropic (b) has an efficiency of 94 percent
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Find the minimum film thickness for a journal bearing with the data below. shaft diameter, d-50 mm, clearance ratio, cdratio? 0.001, shaft speed, n 2000 rpm; bearing length. i 200 mm; eccentricity ration, ? -0.55. ( note, cdratio-ca/d) the minimum film thickness is um
Answers: 2
You know the right answer?
Questions What is the necessary preparations expected to be done on the surface of a ferrous metal w...
Questions
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 02.10.2019 19:30
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 02.10.2019 19:30
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 02.10.2019 19:30
![question](/tpl/images/cats/health.png)
Health, 02.10.2019 19:30
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 02.10.2019 19:30
![question](/tpl/images/cats/ekonomika.png)
Business, 02.10.2019 19:30
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 02.10.2019 19:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 02.10.2019 19:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 02.10.2019 19:30
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 02.10.2019 19:30
![question](/tpl/images/cats/himiya.png)
Chemistry, 02.10.2019 19:30
![question](/tpl/images/cats/himiya.png)
Chemistry, 02.10.2019 19:30