![subject](/tpl/images/cats/User.png)
Engineering, 24.09.2021 07:40 genyjoannerubiera
Which of these devices has 3000-A fuses that provide fault protection for the 4000-A, 480/277-V, 3-phase bus that feeds seven circuits?
A. Feeder compartments
B. Metering component
C. Main circuit disconnect
D. Incoming line department
![ansver](/tpl/images/cats/User.png)
Answers: 3
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
At 12 noon, the count in a bacteria culture was 400; at 4: 00 pm the count was 1200 let p(t) denote the bacteria cou population growth law. find: (a) an expression for the bacteria count at any time t (b) the bacteria count at 10 am. (c) the time required for the bacteria count to reach 1800.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Assuming compressible flow of air and that the measurements are done at flagstaff a pitot static tube that gives the difference of total and static pressure measures 0.35 m of mercury. what is the velocity of air? assume the temperature to be 300k. (submit your excel or matlab calculation sheet)
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
You know the right answer?
Which of these devices has 3000-A fuses that provide fault protection for the 4000-A, 480/277-V, 3-p...
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 22.06.2019 04:30
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/fizika.png)
Physics, 22.06.2019 04:30
![question](/tpl/images/cats/mat.png)
Mathematics, 22.06.2019 04:30
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 22.06.2019 04:30
![question](/tpl/images/cats/istoriya.png)
History, 22.06.2019 04:30
![question](/tpl/images/cats/en.png)
English, 22.06.2019 04:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
English, 22.06.2019 04:30
![question](/tpl/images/cats/mat.png)
Mathematics, 22.06.2019 04:30
![question](/tpl/images/cats/mat.png)
Mathematics, 22.06.2019 04:30
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/en.png)
English, 22.06.2019 04:30