Engineering, 10.12.2021 18:30 Riley3833

25. Ratchets and Screwdrivers are the same tool. True or False
26. A battery tester can be used to jump start a vehicle.
True or False
27. An adjustable wrench is good to have as it can be changed to fit any nut size. True or False
28. A Mechanic stethoscope is specially designed so that the noises produced by a problem in the vehicle can be identified.
True or False
29. A Compression Tester test the performance of the engine valves and piston rings. True or False
30. A battery pack is a good tool to have when travelling.
True or False
31. Using the correct size hand tool makes it easier to tighten or loosen nuts, bolts and screws.
True or False
32. A computer scanner can tell you every problem in a vehicle.
True or False
33. A Breaker Bar gives the same torque as regular length wrenches. True or False
34. A Pilot Bearing Puller can also be used to pull out a Crankshaft. True or False
25. Ratchets and Screwdrivers are the same tool.
True or False
26. A battery tester can be used to jump start a vehicle.
True or False
27. An adjustable wrench is good to have as it can be changed to fit any nut size. True or False
28. A Mechanic stethoscope is specially designed so that the noises produced by a problem in the vehicle can be identified.
True or False
29. A Compression Tester test the performance of the engine valves and piston rings. True or False
30. A battery pack is a good tool to have when travelling.
True or False
31. Using the correct size hand tool makes it easier to tighten or loosen nuts, bolts and screws.
True or False
32. A computer scanner can tell you every problem in a vehicle.
True or False
33. A Breaker Bar gives the same torque as regular length wrenches. True or False
34. A Pilot Bearing Puller can also be used to pull out a Crankshaft. True or False

Answers: 3

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Machinery that is a key part of the process and without which the plant or process cannot function is classifed as: (clo4) a)-critical machinery b)-essential machinery c)-general purpose machinery d)-none of the specified options.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

An air compression refrigeration system is to have an air pressure of 100 psia in the brine tank and an allowable air temperature increase of 60°f for standard vapor compression cycle temperatures of 77 f entering the expansion cylinder and 14 f entering the compression cylinder, calculate the coefficient of performance a. 2.5 b 3.3 c. 4.0 d. 5.0

Answers: 3

Answer

Engineering, 04.07.2019 18:20

Most leaks in reciprocating air compressors can be detected and minimized by: (clo4) a)-detecting leakage areas using ultrasonic acoustic detector. b)-tightening joints and connections c)-replacing faulty equipment d)-all of the given options

Answers: 2

Answer

You know the right answer?

25. Ratchets and Screwdrivers are the same tool. True or False
26. A battery tester can be...

Questions