subject

Health, 21.01.2021 19:50 acharity196

19. What is an early bloomer? an adolescent who is unable to resist peer pressure

an adolescent who develops before most of his or her peers

an adolescent who develops after most of his or her peers

an adolescent who fails to show secondary sex characteristics

ansver

Answers: 1

Show answers

Another question on Health

question

Health, 23.06.2019 00:00

According to proper standing posture, from a side view, which parts of the body should be aligned? a. ear, shoulder, hip, knee, and ankle b. stomach, hip, knee, and ankle c. nose, shoulder, hip, knee d. ear, shoulder, fingers, ankle

Answers: 2

question

Health, 23.06.2019 14:20

Being prepared to play is an important step in staying safe when participating in a game. select the best answer from the choices provided. t f

Answers: 1

question

Health, 23.06.2019 18:30

Which activity causes the greatest risk of driving fatalitiesa. driving at nightb.driving while distractedc.driving with a passengerd.driving on a clear day

Answers: 1

question

Health, 23.06.2019 19:30

What if you were not responsible for planning the menu, and you noticed that the portions provided were often very large? what resource(s) could you use to understand the appropriate portion sizes for children? a. national and state health standards b. cooking course c. ask parents d. ask the school nurse and guidance counselor

Answers: 2

You know the right answer?

19. What is an early bloomer? an adolescent who is unable to resist peer pressure

an ad...

Questions

question

Engineering, 11.07.2019 01:10

In what kind of diffusion processes do we use fick's i and il laws? explain all the parameters (c c(x, t), co, t, and x) shown in the diffusion curve...

question

Engineering, 11.07.2019 01:10

Acapacitance sensor consists of two overlapping plates separated by a small gap filled with either a dielectric material or a vacuum. capacitance is c...

question

Engineering, 11.07.2019 01:10

Across-flow air-to-water heat exchanger (both fluids unmixed) with an effectiveness of 0.65 is used to heat water (cp 4180 j/kg. k) with hot air (c 10...

question

Engineering, 11.07.2019 01:10

Determine the bending stress at the surface of a 3-in.-diameter shaft subjected to a bending moment of 3200 lb-ft....

question

Engineering, 11.07.2019 01:10

Consider a spent nuelear fuel rod of constant thermal conductivity k, perimeter p, length l, and uniform cross-sectional area ac. energy is released a...

question

Engineering, 11.07.2019 01:10

An ideal gas of butane in a piston-cylinder device is initially at 8a fahrenheit and 1 bar undergoes a thermodynamic cycle consisting of three process...

question

Engineering, 11.07.2019 01:10

Calculate the speed of a (i) 0.5-mev electron. ii) 25-mev electron. (b) how much greater than the rest mass is the mass of each of the energetic elect...

question

Engineering, 11.07.2019 01:10

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

question

Engineering, 11.07.2019 01:10

A16-bit aid converter has a full-scale range+10 v. what is the resolution of this a/d in volts? if this a/d were used to measure temperature using a...

question

Engineering, 11.07.2019 01:10

List the different types of solar cells and their efficiency ranges...

question

Engineering, 11.07.2019 01:10

Assuming the following, what is the fill factor for the following solar cell? power=100w voc=30v isc=10a...

question

Engineering, 11.07.2019 01:10

Increasing temperature will reduce the corrosion rate. a)-true b)- false...

question

Engineering, 11.07.2019 01:10

The yield stress of a tension specimen machined from a 2-m wide by 0.6-cm thick copper sheet is 145 mpa. the sheet is rolled further with an applied t...

question

Engineering, 11.07.2019 01:10

Asampling of 409 motor shafts from a very large production batch shows a sample standard deviation in diameter of 0.021 mm with a sample mean of 9.251...

question

Engineering, 11.07.2019 01:10

Explain the aerodynamics of airbus a380 in terms of 1)- l/d 2)- cl max 3)- cd...

question

Engineering, 11.07.2019 01:10

Derive the expression for the thermal efficiency of an air standard bray ton cycle in terms of the pressure ratio and the ratio of specific heats....

question

Engineering, 11.07.2019 01:10

(a) calculate the speed of a 25-mev proton (b) what is the percent increase in mass of this proton over its rest mass?...

question

Engineering, 11.07.2019 01:10

Explain the moire's method and discuss the mismatch techniques of moire's strain analysis with fringe ordering....

question

Engineering, 11.07.2019 01:10

Which of the following is not project objectives' characteristies? a)- complex b)- realistic c)- time related...

question

Engineering, 11.07.2019 01:10

The initial volume of 0.2 kg of gas was 0.15 m' at a temperature of 288 k and a pressure of 1,03 x 10' nm': after adiabatie compression to 0.054 m',...

More questions: Health Another questions

Questions on the website: 13722367