History, 27.05.2020 19:05 alyssalopez9023

Considerando as relações existentes
entre o Humanismo e o Renascimento,
pode-se afirmar CORRETAMENTE que:
Escolha uma:
a. O Humanismo constitui uma viso
de mundo que permitiu o resgate da
herança greco-romana
b. O Humanismo fazia uma severa
crítica a herança greco-romana.
c. O Humanismo e o Renascimento,
embora sendo movimentos
contemporâneos, eram bem distintos
e não apresentavam semelhanças.
d. O Humanismo constitui um
movimento filosófico contrário ao
Renascimento

Answers: 2

Show answers

Another question on History

History, 20.06.2019 18:04

The commander of the army or the would become more powerful and more important than the emperor of japan

Answers: 2

Answer

History, 21.06.2019 16:30

What was the main point of truman doctrine ?

Answers: 2

Answer

History, 22.06.2019 07:20

Which of the following was a factor in the development of the english common law ?

Answers: 1

Answer

History, 22.06.2019 08:10

Atype of infrastructure that state governments maintain is schools roads libraries parks

Answers: 1

Answer

You know the right answer?

Considerando as relações existentes
entre o Humanismo e o Renascimento,
pode-se afirmar...

Questions

Engineering, 14.09.2019 02:10

The condition of irrotationality for a two-dimensional flow is satisfied when rotation w everywhere is (less than — equal to — more than) zero....

Engineering, 14.09.2019 02:10

The flow of a real fluid has (more —less - same ) complexity of an ideal fluid, owing to the phenomena caused by the existence of (viscosity-pressure...

Engineering, 14.09.2019 02:10

In laminar now, fluid particles are constrained to motion in (parallel —perpendicular opposite) paths by the action of (temperature- viscosity —pressu...

Engineering, 14.09.2019 02:10

Which of the following is not a function of a plc programming device? a. to enter the user program b. to monitor the user program c. to execute the u...

Engineering, 14.09.2019 02:10

Acertain measurement is performed 50 times. the arithmetic mean reading is 7.163 ft., and the standard deviation is 0.01 ft. how many readings fall wi...

Engineering, 14.09.2019 02:10

Apolyimide photoresist requires 90 mj/cm^2 per micron of thickness to be developed properly. if a lamp provides 900 w/m, how long does it take to expo...

Engineering, 14.09.2019 02:10

Determine ixx for the cylinder with a concentarted circular hole. the mass of body is m...

Engineering, 14.09.2019 02:10

Two 14.5° pressure angle, mating, 5-pitch gears have 30 and 110 teeth. in practice, the gears are mounted at a center distance 0.7 inches greater than...

Engineering, 14.09.2019 02:10

The center distance of two spur gears that have 20° pressure angle and full-depth with diametral pitch of 8 teeth/in, is increased by 0.05 in over the...

Engineering, 14.09.2019 02:10

Two meshing 24-pitch, 25° pressure angle gears have n1-24 and n2 60 teeth. the in use center distance of the two gears is 0.16 inches larger than the...

Engineering, 14.09.2019 02:10

Batteries are used in a plc's processor to a. maintain data in nonvolatile memory when line power is removed from the processor. b. maintain data in v...

Engineering, 14.09.2019 02:10

Acomplex cmos fabrication process requires 25 masks a. what fraction of the dice must be good (i. e. what yield must be obtained) during each mask ste...

Engineering, 14.09.2019 02:10

Draw and label a typical true stress-strain curve for a ductile material....

Engineering, 14.09.2019 02:10

Draw and label a typical engineering stress-strain curve for a brittle material....

Engineering, 14.09.2019 02:10

Determine the length l of each of the slender rods of mass m/2 which must be centrally attached to the faces of the thin homogeneous disk of mass m in...

Engineering, 14.09.2019 02:10

Afour-stroke cycle engine delivers a torque of 437 ft-lb at the flywheel (output shaft) when the engine speed is 2100 rpm while using 514 hp of fuel e...

Engineering, 14.09.2019 02:10

It takes a man 12.5 hours to complete a 500-mile trip in his automobile, during which 18 gallons of gasoline are consumed. during this trip, the avera...

Engineering, 14.09.2019 02:10

For a motor purchased for a tank project, it claims that at 12v it produces 6000 rpm. this motor is attached to a 50: 1 gear reduction gearbox. the ou...

Engineering, 14.09.2019 02:10

Which of the two materials (brittle vs. ductile) usually obtains the largest modulus of toughness and why?...

Engineering, 14.09.2019 02:10

Afour-cylinder chrysler si engine has the following characteristics: 2.2l displacement, 87.5 mm bore, 92 mm stroke, 8.9 compression ratio, and a maxi...

More questions: History Another questions