Angela constructs a parallel line pq to a given line ab through a point not on line ab. first, she carries out her construction by drawing line ef and marking
a random point r along the line. next she uses her compass to draw circle 2 with a center where ab intersects ef and a radius at point d. she draws an
identical circle, circle 2, at point r. angela draws circle 3 which intersects point d on line ab and has a center that occurs where circle 1 intersects line ef.
next, she draws circle 4 with the same dimensions as circle 3 and with a center that occurs where circle 2 intersects line ef. she identifies the point of
intersection of circles 2 and 4, and adds point s. next, she draws a line from point r to point s. using her ruler, angela expands segment rs to construct the
parallel line po
which theorem justifies why angela's construction results in a parallel line through a point r not on the original line ab?
select one:
a. if one pair of lines is congruent, the lines are parallel.
b. if two angles form a linear pair they are supplementary and their lines are parallel.
c. if two lines are cut by a transversal and the corresponding angles are congruent, the lines are parallel.
d. if the midpoints of two lines are connected by a transversal the lines are parallel.

part a

answer: a reasonable domain is where n is a real number. so n can be between 0 and 10. both endpoints are included.

work shown:

n is the number of days after the experiment starts. the smallest n can be is n = 0 which means that 0 days have gone by, and we're at the start. to find out how large n should be, then replace f(n) with 16.13 and solve for n. use logarithms to isolate the exponent.

f(n) = 12*(1.03)^n

16.13 = 12*(1.03)^n

16.13/12 = (1.03)^n

1.34416666666667 = (1.03)^n

(1.03)^n = 1.34416666666667

log[ (1.03)^n ] = log[ 1.34416666666667 ]

n*log[ 1.03 ] = log[ 1.34416666666667 ]

n = log[ 1.34416666666667 ]/log[ 1.03 ]

n = 10.0062999823929

this rounds to n = 10 which is fairly close but not 100% perfect. so this is the largest n can be.

note: if you plug n = 10 into f(n), you'll get roughly 16.127 which rounds to 16.13 (this comes up again in part c)

=====================================

part b

answer: the y intercept is 12. it represents the starting height of the plant in cm.

work shown:

plug n = 0 into the f(n) function. simplify

f(n) = 12*(1.03)^n

f(0) = 12*(1.03)^0

f(0) = 12*(1)

f(0) = 12

on day n = 0, aka the starting point, the height f(n) is 12 cm

=====================================

part c

answer: the average rate of change is approximately 0.43061036458991 (round however you need to). this represents the average growth rate from day n = 3 to day n = 10. so the plant grew roughly 0.43 cm per day during this timespan, assuming you round to 2 decimal places.

work shown:

compute f(3)

f(n) = 12*(1.03)^n

f(3) = 12*(1.03)^3

f(3) = 13.112724 < we'll use this later

compute f(10)

f(n) = 12*(1.03)^n

f(10) = 12*(1.03)^10

f(10) = 16.1269965521294 < we'll use this later

now use the formula below with a = 3 and b = 10

aroc = average rate of change

aroc = [ f(b) - f(a) ]/[ b - a ]

aroc = [ f(10) - f(3) ]/[ 10 - 3 ]

aroc = (16.1269965521294 - 13.112724)/(10 - 3)

aroc = 3.0142725521294/7

aroc = 0.43061036458991

round this however you need to

note: the plant grew approximately 3.01 cm over 7 days, so roughly 0.43 cm per day is the average growth rate (if you were to round to 2 decimal places).

47 - 90 = 43

43 - 180 = x

x = 137

step-by-step explanation:

because 1/3 is a fraction. we can tell because there is a divisor symbol between the 1 and the 3. if we were to add 2 fractions together, we would add the numerators, which is the number on top, but not the denominators, which is the number on the bottom

1/3+1/3=2/3

hope this !