subject

Mathematics, 23.09.2019 14:30 rodfam13716

Carlos drove 207 miles on 6 gallons of gasoline. assuming he maintains this rate, how many miles could he drive on 11 gallons of gasoline?

ansver

Answers: 1

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 13:30

The factorization of 8x3 -125 is (2x-5)(jx2 +kx+25)

Answers: 1

question

Mathematics, 21.06.2019 19:00

Twenty points. suppose that one doll house uses the 1 inch scale, meaning that 1 inch on the doll house corresponds to 1/2 foot for life-sized objects. if the doll house is 108 inches wide, what is the width of the full-sized house that it's modeled after? in inches and feet

Answers: 2

question

Mathematics, 21.06.2019 20:00

One hectometer is a) 1/1000 of a meter. b) 1/100 of a meter. c) 10 meters. d) 100 meters. e) 1000 meters.

Answers: 1

question

Mathematics, 22.06.2019 00:00

The construction of copying qpr is started below. the next step is to set the width of the compass to the length of ab. how does this step ensure that a new angle will be congruent to the original angle? by using compass take the measures of angle and draw the same arc according to it.

Answers: 2

You know the right answer?

Carlos drove 207 miles on 6 gallons of gasoline. assuming he maintains this rate, how many miles cou...

Questions

question

Engineering, 26.07.2019 20:10

What causes a shock to detach from the surface of an object?...

question

Engineering, 26.07.2019 20:10

Consider two solid blocks, one hot and the other cold, brought into contact in an adiabatic container. after a while, thermal equilibrium is establish...

question

Engineering, 26.07.2019 20:10

Steam at 500 psia and 600 f is cooled at constant volume to the state of 100 psia. the heat removed from the steam enters the environment at 60 f. fin...

question

Engineering, 26.07.2019 20:10

Avolcanic plume puts ash into the atmosphere to altitude of 1m. the characteristic ash particle is a sphere with a diameter of 40 um and has a density...

question

Engineering, 26.07.2019 20:10

Consider a steam power plant that operates on the ideal reheat rankine cycle. the plant maintains the boiler at 5,000 kpa, the reheat section at 1,200...

question

Engineering, 26.07.2019 20:10

Pressurized steam at 540 k flows through a long, thin-walled pipe of 0.6-m diameter. the pipe is enclosed in a concrete casing that is of square cross...

question

Engineering, 26.07.2019 20:10

Rank the six microstructures of steel in general order of least ductile to most ductile.(bainite, coarse pearlite, fine pearlite, martensite, spheroid...

question

Engineering, 26.07.2019 20:10

In regard to low pressure die casting, high pressure die casting and squeeze casting of aluminium alloys, briefly compare the following process charac...

question

Engineering, 26.07.2019 20:10

A2d, incompressible flow field is described by the stream function φ= -(ax^2-ay^2). a. is the flow possible? b. is the flow field a potential flow fi...

question

Engineering, 26.07.2019 20:10

(a) briefly describe, aided with schematic drawings, the operation principles of the two 6. powder bed (selective laser melting and selective electron...

question

Engineering, 26.07.2019 20:10

Steam at a pressure of 15 bar and a temperature of 320 °c is contained in a large vessel. connected to the vessel through a valve is a turbine followe...

question

Engineering, 26.07.2019 20:10

Awaste gas stream containing 190 ppm by volume ) vinyl chloride is to be treated with activated carbon ina packed bed at a rate of 20 m3/min to reduce...

question

Engineering, 26.07.2019 20:10

Casting of a plate is made in a metal mould where heat transfer is controlled at the mould- metal interface. ignore the superheat of the liquid metal...

question

Engineering, 26.07.2019 20:10

Consider two long, poles of same diameter and uniform cross sectional area throughout its length but different materials. the ends of each rod is atta...

question

Engineering, 26.07.2019 20:10

What is the quality of a two-phase liquid-vapor mixture of h20 at 20 °c with a specific volume of 10 m^3/kg?...

question

Engineering, 26.07.2019 20:10

Consider cutting tool materials, answer which cutting material is suitable, considering manufacturing costs, for each of the major metallic alloy (al...

question

Engineering, 26.07.2019 20:10

Describe the challenges associated with fusion welding of dissimilar metals. your description should cover all the parameters and /or factors to be co...

question

Engineering, 26.07.2019 20:10

Abuilding has a net space heating load of 100,000 btu/hr. if the combined piping and pickup alowance is 15%, what a)- 100,000 btu/hr b)- 115,000 btuhr...

question

Engineering, 26.07.2019 20:10

That the larger volume of chimney will enhance natural convection is due to (a) higher thermal conductivity (c) larger radiation surface area (b) incr...

question

Engineering, 26.07.2019 20:10

Name one aluminium alloy used in low pressure die casting and one in high pressure die casting? explain the major reasons why one is different to the...

More questions: Mathematics Another questions

Questions on the website: 13722367