subject

Mathematics, 15.05.2020 08:57 mari33312

Can someone explain this

Can someone explain this

ansver

Answers: 2

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 19:30

Solve the following inequalities and show the solution on a number line. 2x+3< 3(4x+5)

Answers: 1

question

Mathematics, 21.06.2019 20:30

Aswimming pool had 2.5 million liters of water in it. some water evaporated, and then the pool only had 22 million liters of water in it. what percent of the water evaporated?

Answers: 2

question

Mathematics, 21.06.2019 21:20

Rose bought a new hat when she was on vacation. the following formula describes the percent sales tax rose paid b=t-c/c

Answers: 3

question

Mathematics, 21.06.2019 23:00

Jane’s favorite fruit punch consists of pear, pineapple, and plum juices in the ratio 5: 2: 3. how many cups of pear juice should she use to make 20 cups of punch?

Answers: 1

You know the right answer?

Can someone explain this
...

Questions

question

Engineering, 11.07.2019 02:20

Adisk-shaped part is to be cast out of aluminum. the diameter 500 mm and thickness = 20 mm. if the mold constant = 3.0 s/mm2 in chvorinov's rule, how...

question

Engineering, 11.07.2019 02:20

The areas of conflict between public and private include. a)-the areas of conflict between public and private include. b)- lack of communication. c)-...

question

Engineering, 11.07.2019 02:20

Adiving board is to be designed that is 6 foot long, 14in wide. the maximum load at the end of the beam is 400lb. the diving board can be considered a...

question

Engineering, 11.07.2019 02:20

Liquid water at 300 kpa and 20°c is heated in a chamber by mixing it with superheated steam at 300 kpa and 300°c. cold water enters the chamber at a r...

question

Engineering, 11.07.2019 02:20

An adiabatic air compressor takes in air at 100 kpa, 25 °c and delivers it at 1500 kpa, 364 °c to a constant-pressure air cooler, which the air exits...

question

Engineering, 11.07.2019 02:20

Pressurized steam at 460k flows through a long, thin walled pipe of 0.5m diameter. the pipe is enclosed in a concrete casting that is of a square cros...

question

Engineering, 11.07.2019 02:20

Observe the depth of the case and any evidence of decarburizing in the outer case of the quenched sample....

question

Engineering, 11.07.2019 02:20

Asteel sphere with a diameter of 7.6 cm is to be hardened by first heating it to a uniform temperature of 870c and then quenching it in a large bath o...

question

Engineering, 11.07.2019 02:20

Agas power cycle has air entering at 0.7 bar and 260 k. the compressor pressure ratio is 25: 1 and its outlet temperature is 720 k. the combustor heat...

question

Engineering, 11.07.2019 02:20

Determine size of a standard square key made of 1045 hot rolled steel for a 2 inch dia shaft transmitting 100 hp at 500 rpm with factor of safety 2.5...

question

Engineering, 11.07.2019 02:20

Asquare duct with a 10pa/m pressure drop, .001 pa-s viscosity, and a duct side of .1m with a length of 1m is compared to a circular pipe. compute a)-w...

question

Engineering, 11.07.2019 02:20

Apreheater involves the use of condensing steam at 100°c on the inside of a bank of tubes to heat air that enters at 1 atm and 25°c. the air moves at...

question

Engineering, 11.07.2019 02:20

Consider the heating of a fluid in a tube of constant cross section whose inner surface is maintained at a constant temperature the temperature differ...

question

Engineering, 11.07.2019 02:20

Design a solid steel shaft to transmit 14 hp at a speed of 2400rpm f the allowable shearing stress is given as 3.5 ksi....

question

Engineering, 11.07.2019 02:20

In flow across the tube banks, the reynolds number is based on the maximum velocity instead of the uniform approach velocity a)-true b)-false...

question

Engineering, 11.07.2019 02:20

Consider laminar (for the entire tube) forced convection in a circular tube. heat fux near the inlet of the tube is higher than the heat flux near the...

question

Engineering, 11.07.2019 02:20

The steady-state temperature distribution in a one-dimensional wall of thermal conductivity k and thickness l is of the form t= ar' + br' + cr + d. de...

question

Engineering, 11.07.2019 02:20

Consider the following fluids, each with a velocity of v = 5 m/s and a temperature of to-20°c, in cross flow over a 10-mm-diameter cylinder maintained...

question

Engineering, 11.07.2019 02:20

A25hp, 1750-rpm electric motor drives a machine through a multiple v-belt drive. the driver sheave is 3.7 in. in diameter and the wrap angle of the dr...

question

Engineering, 11.07.2019 02:20

In hydrodynamically fully developed region at a cross section no longer changes in the direction of flow a)-dimensionless temperature profile b)-veloc...

More questions: Mathematics Another questions

Questions on the website: 13722359