Mathematics, 11.02.2021 08:20 ValeryGi3721

Hi good night i was wondering if anyone can help me with these questions plzz plz

Hi good night i was wondering if anyone can help me with these questions plzz plzzzz

Answers: 2

Show answers

Another question on Mathematics

Mathematics, 21.06.2019 16:00

On a piece of paper graph f(x)=5•(0.4)^x

Answers: 1

Answer

Mathematics, 21.06.2019 16:40

This question awards 100 ! i really don’t want to fail i will also mark you !

Answers: 2

Answer

Mathematics, 21.06.2019 17:30

Janet drove 300 miles in 4.5 hours. write an equation to find the rate at which she was traveling

Answers: 2

Answer

Mathematics, 21.06.2019 17:40

Bradley hikes 12 miles in 3 hours. in relation to bradley’s hike, which statement describes the expression

Answers: 2

Answer

You know the right answer?

Hi good night i was wondering if anyone can help me with these questions plzz plz
...

Questions

Engineering, 26.07.2019 20:10

Air initially at 15 psla and 60 f is compressed to 75 psia and 400 f. the power input to air under steady state condition is 5 hp and heat loss of 4 b...

Engineering, 26.07.2019 20:10

How does the thermal efficiency of an ideal cycle, in general, compare to that of a carnot cycle operating between the same temperature limits?...

Engineering, 26.07.2019 20:10

Agas turbine cycle using brayton cycle with both intercooler and regenerators air and split ideal compressor and turbine, enters in the compressor at...

Engineering, 26.07.2019 20:10

Define the isentropic efficiency for each of the following 3. a. i. adiabatic turbine ii. adiabatic compressor iii. adiabatic nozzle...

Engineering, 26.07.2019 20:10

What causes a shock to detach from the surface of an object?...

Engineering, 26.07.2019 20:10

Consider two solid blocks, one hot and the other cold, brought into contact in an adiabatic container. after a while, thermal equilibrium is establish...

Engineering, 26.07.2019 20:10

Steam at 500 psia and 600 f is cooled at constant volume to the state of 100 psia. the heat removed from the steam enters the environment at 60 f. fin...

Engineering, 26.07.2019 20:10

Avolcanic plume puts ash into the atmosphere to altitude of 1m. the characteristic ash particle is a sphere with a diameter of 40 um and has a density...

Engineering, 26.07.2019 20:10

Consider a steam power plant that operates on the ideal reheat rankine cycle. the plant maintains the boiler at 5,000 kpa, the reheat section at 1,200...

Engineering, 26.07.2019 20:10

Pressurized steam at 540 k flows through a long, thin-walled pipe of 0.6-m diameter. the pipe is enclosed in a concrete casing that is of square cross...

Engineering, 26.07.2019 20:10

Rank the six microstructures of steel in general order of least ductile to most ductile.(bainite, coarse pearlite, fine pearlite, martensite, spheroid...

Engineering, 26.07.2019 20:10

In regard to low pressure die casting, high pressure die casting and squeeze casting of aluminium alloys, briefly compare the following process charac...

Engineering, 26.07.2019 20:10

A2d, incompressible flow field is described by the stream function φ= -(ax^2-ay^2). a. is the flow possible? b. is the flow field a potential flow fi...

Engineering, 26.07.2019 20:10

(a) briefly describe, aided with schematic drawings, the operation principles of the two 6. powder bed (selective laser melting and selective electron...

Engineering, 26.07.2019 20:10

Steam at a pressure of 15 bar and a temperature of 320 °c is contained in a large vessel. connected to the vessel through a valve is a turbine followe...

Engineering, 26.07.2019 20:10

Awaste gas stream containing 190 ppm by volume ) vinyl chloride is to be treated with activated carbon ina packed bed at a rate of 20 m3/min to reduce...

Engineering, 26.07.2019 20:10

Casting of a plate is made in a metal mould where heat transfer is controlled at the mould- metal interface. ignore the superheat of the liquid metal...

Engineering, 26.07.2019 20:10

Consider two long, poles of same diameter and uniform cross sectional area throughout its length but different materials. the ends of each rod is atta...

Engineering, 26.07.2019 20:10

What is the quality of a two-phase liquid-vapor mixture of h20 at 20 °c with a specific volume of 10 m^3/kg?...

Engineering, 26.07.2019 20:10

Consider cutting tool materials, answer which cutting material is suitable, considering manufacturing costs, for each of the major metallic alloy (al...

More questions: Mathematics Another questions