Mathematics, 08.10.2019 02:30 priscillaan

Using the order of operations, what is the last calculation that should be done to evaluate 4(8 - 6)5² - 6 ÷ (–3)?

Answers: 2

Show answers

Another question on Mathematics

Mathematics, 20.06.2019 18:04

How do you divide 9/4 divided by 10/3

Answers: 1

Answer

Mathematics, 21.06.2019 18:30

Find the exact value of each of the following. in each case, show your work and explain the steps you take to find the value. (a) sin 17π/6 (b) tan 13π/4 (c) sec 11π/3

Answers: 2

Answer

Mathematics, 21.06.2019 19:00

Write the expression in complete factored form. 5n_(c - 3) - n(c - 3) =

Answers: 2

Answer

Mathematics, 21.06.2019 19:30

Can someone me with these two circle theorem questions asap?

Answers: 2

Answer

You know the right answer?

Using the order of operations, what is the last calculation that should be done to evaluate 4(8 - 6)...

Questions

Physics, 14.09.2019 03:30

Gamma rays (γ-rays) are high-energy photons. in a certain nuclear reaction, a γ-ray of energy 0.815 mev (million electronvolts) is produced. compute t...

Engineering, 14.09.2019 03:30

What is 220 c in degrees fahrenheit (f)?...

Engineering, 14.09.2019 03:30

Apiston at rest, filled with a gas, is adiabatically compressed from an initial state at 790 mm hg and 3 ft' to a final state of 1100 mm hg and 2 ft'....

Engineering, 14.09.2019 03:30

Calculate the rate at which body heat is conducted through the clothing of a skier in a steady- state process, given the following data: the body sur...

Engineering, 14.09.2019 03:30

Hows many channels of data acquisition will be used for the experiment? a. two b. one c. three d. four...

Engineering, 14.09.2019 03:30

An experiment was set-up to measure an unknown fluid's viscosity. two flat plates are separated by a gap of 4.5 mm and move relative to each other at...

Engineering, 14.09.2019 03:30

Fluid flowing through a constriction or partially opened valve in a pipe system may develop localized low pressures due to increased velocity. if a pi...

Engineering, 14.09.2019 03:30

What is the ratio between the maximum elastic moment, my, and the maximum plastic moment, mp, for a solid rectangular section made from a ductile, ela...

Engineering, 14.09.2019 03:30

Abrittle intermetallics specimen is tested with a bending test. the specimen's width 0.45 in and thickness 0.20 in. the length of the specimen between...

English, 14.09.2019 03:30

Why does kate chopin choose to tell “the story of an hour” in third person versus from the perspective of a main character? use evidence from the sto...

Engineering, 14.09.2019 03:30

Based on results of a tensile test, the flow curve has parameters are the following: strain-hardening exponent=0.40 and strength coefficient =551.6 m...

Engineering, 14.09.2019 03:30

How to draw an acceptable free body diagram of a car on a slope? force exerted by the motor is denoted by fm. m = 2000kg. angle of slope = 15degrees....

Engineering, 14.09.2019 03:30

Air enters an insulated turbine operating at steady state at 120 psia, 900°r, and 500 ft/s. the exit conditions are 15 psia, 580°r, and 30 ft/s. there...

Engineering, 14.09.2019 03:30

A35cm x 35 cm x 35 cm cubical-shaped vacuum chamber with a 4.0 cm aperture is attached to a direct-drive rotary vane pump with a pumping speed of 8.0...