subject

Mathematics, 26.05.2021 15:30 greenhusky

The lengths of two sides of a triangle are 5 cm and 8 cm. Between what two measures

ansver

Answers: 2

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 17:30

Any is very appreciated! (picture is provided below)not sure how to do this at all won't lie

Answers: 1

question

Mathematics, 21.06.2019 20:10

The constitution gives congress the power to create federal courts lower than the supreme court higher than the supreme court equal to the supreme court, unaffected by the supreme court.

Answers: 1

question

Mathematics, 21.06.2019 21:50

Aparticular telephone number is used to receive both voice calls and fax messages. suppose that 25% of the incoming calls involve fax messages, and consider a sample of 25 incoming calls. (a) what is the expected number of calls among the 25 that involve a fax message?

Answers: 1

question

Mathematics, 21.06.2019 22:10

2. using calculations based on a perpetual inventory system, determine the inventory balance altira would report in its august 31, 2021, balance sheet and the cost of goods sold it would report in its august 2021 income statement using the average cost method. (round "average cost per unit" to 2 decimal places.)

Answers: 1

You know the right answer?

The lengths of two sides of a triangle are 5 cm and 8 cm. Between what two measures...

Questions

question

Engineering, 26.07.2019 17:20

In turning, if the spindle speed (spindle rpm) increases by a factor of four, while the feed rate decreases by a factor of four, will the ideal surfac...

question

Engineering, 26.07.2019 17:20

Oil, with a density of ρ = 900 kg m=3 and a kinematic viscosity of v = 0.1 m^2 s^-1, flows at a volume flow rate of q 0.2 m^3 s^-1 through 500 m of 20...

question

Engineering, 26.07.2019 17:20

What is an involute profile and why is it used in gear tooth design?...

question

Engineering, 26.07.2019 17:20

If i can live with a 3% probability of failure, select a ball bearing design (independent of shaft diameter that will carry a 120 ib load at 3000 rpm....

question

Engineering, 26.07.2019 17:20

Determine the diameter of a cylindrical capillary tube needed to observe a 0.4" rise for water if the contact angle is 12°...

question

Engineering, 26.07.2019 17:20

If a cutting operation is performed at a feed rate of 5 in/min, and the feed is 0,005 in/rev, then the spindle rpm is: i. 5000 rpm. i. 1000 rpm. ili....

question

Engineering, 26.07.2019 17:20

Describe the general steps in the journal bearing design procedure. outline approach with substeps identified is fine....

question

Engineering, 26.07.2019 17:20

How are the pressure angle, pitch circle and base circle for a gear set related?...

question

Engineering, 26.07.2019 17:20

You need to design a compound reverted gear train with a 25: 1 gear ratio. (a) explain how you would go about developing this design. (b) if you were...

question

Engineering, 26.07.2019 17:20

One of the following is an extensive property: a)- density b)- volume c)- pressure d)-none of the above...

question

Engineering, 26.07.2019 17:20

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

question

Engineering, 26.07.2019 17:20

Tool wear rate decreases with increasing: i. machining velocity and work material hardness. ii. cutting tool hardness. ii. none of the above. iv. not...

question

Engineering, 26.07.2019 17:20

Define the following terms. a drawing with the terms labeled would also be where appropriate. a. pitch circle/pitch diameter b. pinion/gear c. base c...

question

Engineering, 26.07.2019 17:20

5kg of wood is burnt in an insulated room. take the walls of the room as well as the wood as the system. the internal energy of the room will increase...

question

Engineering, 26.07.2019 17:20

The hardness of a cutting tool increases with increasing temperature. thus, it is always convenient to machine at higher speeds that lead to higher te...

question

Engineering, 26.07.2019 17:20

What are the independent and dependent variables that are taken into account during journal bearing design?...

question

Engineering, 26.07.2019 17:20

You are provided with an epicyclic (planetary) gear train with the following 30, 20 and 70 teeth on the sun, planet and ring gear respectively. (a) dr...

question

Engineering, 26.07.2019 17:20

What is a partial bearing? what is a loading situation that might lead you to use a partial bearing? how did this tie into beauchamp tower's experim...

question

Engineering, 26.07.2019 17:20

Define and give a few benefits of each of three gear train design options?...

question

Engineering, 26.07.2019 17:20

The atmospheric pressure at the top and the bottom of a mountain are read to be 93.8 kpa and 100.5 kpa respectively. if the average density of air is...

More questions: Mathematics Another questions

Questions on the website: 13722362