Mathematics, 27.12.2021 14:00 XAINEE

Find the allowable height for the hypotenuse if the hypotenuse catheters are 4 cm and 9 cm

Answers: 3

Show answers

Another question on Mathematics

Mathematics, 21.06.2019 15:00

1. are the triangles similar and if so why? what is the value of x? show your work.

Answers: 2

Answer

Mathematics, 21.06.2019 18:00

Arecipe calls for 32 fluid ounces of heavy cream.how many 1 pint containers of heavy cream are needed to make the recipe?

Answers: 2

Answer

Mathematics, 21.06.2019 18:40

What value of x is in the solution set of 4x – 12 s 16 + 8x?

Answers: 3

Answer

Mathematics, 21.06.2019 21:00

Consider the polynomials given below. p(x) = x4 + 3x3 + 2x2 – x + 2 q(x) = (x3 + 2x2 + 3)(x2 – 2) determine the operation that results in the simplified expression below. 35 + x4 – 573 - 3x2 + x - 8 a. p+q b. pq c.q-p d. p-q

Answers: 2

Answer

You know the right answer?

Find the allowable height for the hypotenuse if the hypotenuse catheters are 4 cm and 9 cm...

Questions

Engineering, 11.07.2019 01:10

A0.002-m3 steel tank is rapidly filled with air for 10 s. the air enters the tank at 300 k with a mass flow rate of 0.00017 kg/s. the tank initially c...

Engineering, 11.07.2019 01:10

Draw neat diagrams showing three different kinds of cubic unit cells. which one of these ie least commonly observed in metals and why? how do line de...

Engineering, 11.07.2019 01:10

Which of the following statements about atomic vacancy sites in metals is incznrect a)- a vacancy represents the empty space in an otherwise cosed pac...

Engineering, 11.07.2019 01:10

Aheat engine operates between thermal reservoirs of 1000k and 400k. it receives heat at a rate of 200 kw and rejects it at a rate of 90 kw a)- what is...

Engineering, 11.07.2019 01:10

In what kind of diffusion processes do we use fick's i and il laws? explain all the parameters (c c(x, t), co, t, and x) shown in the diffusion curve...

Engineering, 11.07.2019 01:10

Acapacitance sensor consists of two overlapping plates separated by a small gap filled with either a dielectric material or a vacuum. capacitance is c...

Engineering, 11.07.2019 01:10

Across-flow air-to-water heat exchanger (both fluids unmixed) with an effectiveness of 0.65 is used to heat water (cp 4180 j/kg. k) with hot air (c 10...

Engineering, 11.07.2019 01:10

Determine the bending stress at the surface of a 3-in.-diameter shaft subjected to a bending moment of 3200 lb-ft....

Engineering, 11.07.2019 01:10

Consider a spent nuelear fuel rod of constant thermal conductivity k, perimeter p, length l, and uniform cross-sectional area ac. energy is released a...

Engineering, 11.07.2019 01:10

An ideal gas of butane in a piston-cylinder device is initially at 8a fahrenheit and 1 bar undergoes a thermodynamic cycle consisting of three process...

Engineering, 11.07.2019 01:10

Calculate the speed of a (i) 0.5-mev electron. ii) 25-mev electron. (b) how much greater than the rest mass is the mass of each of the energetic elect...

Engineering, 11.07.2019 01:10

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

Engineering, 11.07.2019 01:10

A16-bit aid converter has a full-scale range+10 v. what is the resolution of this a/d in volts? if this a/d were used to measure temperature using a...

Engineering, 11.07.2019 01:10

List the different types of solar cells and their efficiency ranges...

Engineering, 11.07.2019 01:10

Assuming the following, what is the fill factor for the following solar cell? power=100w voc=30v isc=10a...

Engineering, 11.07.2019 01:10

Increasing temperature will reduce the corrosion rate. a)-true b)- false...

Engineering, 11.07.2019 01:10

The yield stress of a tension specimen machined from a 2-m wide by 0.6-cm thick copper sheet is 145 mpa. the sheet is rolled further with an applied t...

Engineering, 11.07.2019 01:10

Asampling of 409 motor shafts from a very large production batch shows a sample standard deviation in diameter of 0.021 mm with a sample mean of 9.251...

Engineering, 11.07.2019 01:10

Explain the aerodynamics of airbus a380 in terms of 1)- l/d 2)- cl max 3)- cd...

Engineering, 11.07.2019 01:10

Derive the expression for the thermal efficiency of an air standard bray ton cycle in terms of the pressure ratio and the ratio of specific heats....

More questions: Mathematics Another questions