subject

Physics, 02.02.2020 02:43 paulesparsa6

If 500 j of energy were added to 1 kg of each of these samples , which would experience the least temperature increase

ansver

Answers: 2

Show answers

Another question on Physics

question

Physics, 22.06.2019 06:00

When you push downward on a book at rest on a table, you feel an upward force. does this force depend on friction? defend your answer.

Answers: 2

question

Physics, 22.06.2019 18:30

Which of the following is not a means to accelerating? question 4 options: a)increase speed b)remain still c)decrease speed d)change direction

Answers: 1

question

Physics, 22.06.2019 18:50

An insulated thermos contains 148 g of water at 72.7 ˚c. you put in a 11.7 g ice cube at 0.00 ˚c to form a system of ice + original water. the specific heat of liquid water is 4190 j/kg•k; and the heat of fusion of water is 333 kj/kg. what is the net entropy change of the system from then until the system reaches the final (equilibrium) temperature?

Answers: 2

question

Physics, 22.06.2019 19:30

In this thread, i would like you to comment on the nature of light and how operation of telescopes. light has a duality of a particle and a wave; which one affects your life? also how does light interact with optics inside telescopic systems? answer these questions in two paragraphs. then respond the another students response.

Answers: 1

You know the right answer?

If 500 j of energy were added to 1 kg of each of these samples , which would experience the least te...

Questions

question

Medicine, 14.09.2019 01:10

This drug used in treating angina acts by dilating the blood vessel. a. beta adrenergic blocker b. nitroglycerin c. calcium channel...

question

Engineering, 14.09.2019 01:10

Give examples of engineering structures which can be modelled as thin walled cylinders....

question

Chemistry, 14.09.2019 01:10

The binary system ethanol (1)/1-butanol (2) should conform closely to raoult's law. a. using antoine's equation, create a txy plot at 300 mm hg with t...

question

Chemistry, 14.09.2019 01:10

Given the following system: ax --x(t)' m(t) +4 where m(t) is an input, and x(t) is a state variable and dt due to physics of the problem x(t) can tak...

question

Engineering, 14.09.2019 01:10

What is the governing ratio for thin walled cylinders?...

question

Chemistry, 14.09.2019 01:10

The gas phase dimerisation reaction takes place in a continuous constant pressure cstr operating at 1 atm total pressure (a) establish the relationshi...

question

Engineering, 14.09.2019 01:10

Two airstreams are mixed stea percent relative humidity retreams are mixed steadily and adiabatically. the first stream enters at 35°c and 30 ont rela...

question

Chemistry, 14.09.2019 01:10

Let's assume you have infinite amount of dilute aqueous solution of gold that only contains gold at a concentration of 1x10.10weight raction. if you w...

question

Engineering, 14.09.2019 01:10

When is it appropriate to model a structural element as a beam?...

question

Engineering, 14.09.2019 01:10

Astrain gauge with a 4 mm gauge length gives a displacement reading of 1.5 um. calculate the stress at the location of the strain gauge if the materia...

question

Engineering, 14.09.2019 01:10

What are the principal advantages of dic over strain gauges?...

question

Engineering, 14.09.2019 01:10

When there is no flow, the signal transit times between ultrasonic sensor pairs are x upstream and downstream. a. not applicable b. same c. different...

question

Engineering, 14.09.2019 01:10

The frequency of the changing zones of pressure corresponds to the x of passing vortices....

question

Engineering, 14.09.2019 01:10

Total flow can be calculated since the distance between two consecutive vortices corresponds to a defined volume....

question

Engineering, 14.09.2019 01:10

Specific internal energy is measured in energy per unit mass dimensions. what is 310 kj/kg in btu/lbm units?...

question

Engineering, 14.09.2019 01:10

The differential transit times of the signals going upstream and downstream is a direct measure of (x)....

question

Engineering, 14.09.2019 01:10

Using a coriolis meter is the only way the particular x of mass flow, density, volume flow, and flow velocity can be measured simultaneously. a. proce...

question

Engineering, 14.09.2019 01:10

It is critical to the measurement that any flow meter is installed in such a manner that is kept full of fluid at all times. a) true b) false...

question

Engineering, 14.09.2019 01:10

When sensors in this kind of flow meter sense a change in tube oscillation what is this phenomena called?...

question

Engineering, 14.09.2019 01:10

Laminar flow is the most desirable for flow measurements in pipes. a) true b) false...

More questions: Physics Another questions

Questions on the website: 13722367