Physics, 24.10.2019 16:43 asmaamasto

While placing a compact disc into a cd player, you notice a small chip on it\'s edge. but you attempt to play the cd anyway by placing the cd into the player\'s deck with the chip at θ0 = 12.6° as measured from the x axis. the cd begins to rotate with angular acceleration α = 2.31 rad/s2. if the cd has been spinning for t = 3.51 s and the disc has a radius of r = 6.00 cm, what are the x–y coordinates of the chip after this time, assuming the center of the disc is located at (0.00,0.00).

Answers: 1

Show answers

Another question on Physics

Physics, 21.06.2019 16:00

As shown in fig. p3.64, a closed, rigid tank fitted with a fine-wire electric resistor is filled with refrigerant 22, initially at 2108c, a quality of 80%, and a volume of 0.01 m3. a 12-volt battery provides a 5-amp current to the resistor for 5 minutes. if the final temperature of the refrigerant is 408c, determine the heat transfer, in kj, from the refrigerant.

Answers: 1

Answer

Physics, 21.06.2019 19:20

Describe the path of the electric current through a circuit?

Answers: 1

Answer

Physics, 21.06.2019 22:00

Aroll in a paper machine is powered by a separately excited dc machine. operating point 1 (under load): the roll typically operates at 764 rpm and must provide 301 nm of torque to oppose the load of the paper. the armature voltage is 230v for this operating point operating point 2 (no load): when the load is removed the speed of the roll increases to 900 rpm (the field characteristics are unchanged) la ea dev m (a) calculate the maximum torque (units of nm) that the motor can supply with this applied voltage (b) calculate the value of the armature resistance, ra (in ohms) (c) at operating point 1 (loaded condition), the field current, i, and the total input power (armature field), are measured to be to be 10 a and 28,600 w respectively. use this information to calculate the value of the field resistance, rf (in ohms). (d) (d) at operating point 1 (loaded condition), calculate the motor efficiency. express your answer as a percent to at least 2 significant digits. (d) if the field voltage is reduced by 1/2, calculate the new stall torque (in nm) of the motor (f). if the field voltage is reduced by 1/2, calculate the new no-load speed (in rad/sec)

Answers: 1

Answer

Physics, 21.06.2019 23:30

Classify the following soils according to the uscs classification system. provide appropriate uscs designations. a) this sample of well-graded gravel with sand was obtained from a large earthen dam in vancouver, canada. the sample has 73% fine to coarse sub-angular gravel, 25% fine to coarse sub-angular sand and 2% fines. the maximum size of the particles is 75 mm. the coefficient of curvature is 2.7, while the uniformity coefficient is 12.4. b) this dark brown and wet soil with a â€śstrong organic odorâ€ť has 100% passing the no. 200 sieve. the liquid limit of the material is 32% when not dried and is 21% when oven-dried. the plastic index is 21% when not dried. c) this sand has 61% predominantly fine sand, 23% silty fines, and 16% fine sub-rounded gravel size. the maximum size is 20 mm. the liquid limit is 33% and the plastic limit is 27%. d) this soil has 74% fine to coarse sub-angular reddish sand and 26% organic and silty dark brown fines. the liquid limit is 37% when not dried and is 26% when oven dried. the plastic index is 6% when not dried.

Answers: 1

Answer

You know the right answer?

While placing a compact disc into a cd player, you notice a small chip on it\'s edge. but you attemp...

Questions