![subject](/tpl/images/cats/fizika.png)
Two forces, F1 and F2, act at a point. F1 has a magnitude of 9.80 N and is directed at an angle of α = 62.0° above the negative xaxis in the second quadrant. F2 has a magnitudeof 5.20 N and is directed at an angle of β = 53.7° below the negative x axis in the third quadrant.
a. What is the x component Fx of the resultant force?
b. What is the y component Fy of the resultant force?
c. What is the magnitude F of the resultant force?
d. What is the angle γ that the resultant force forms with the negative x axis? In this problem, assume that positive angles are measured clockwise from the negative x axis.
![ansver](/tpl/images/cats/User.png)
Answers: 1
Another question on Physics
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/fizika.png)
Physics, 23.06.2019 00:30
Due in 40 explain in terms of frame of reference if you’re inside a moving train everything on the outside can seem to be moving
Answers: 1
![question](/tpl/images/cats/fizika.png)
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
You know the right answer?
Two forces, F1 and F2, act at a point. F1 has a magnitude of 9.80 N and is directed at an angle of α...
Questions
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 10.04.2020 15:31
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 10.04.2020 15:31
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 10.04.2020 15:31
![question](/tpl/images/cats/User.png)
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/es.png)
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 10.04.2020 15:33
![question](/tpl/images/cats/istoriya.png)
History, 10.04.2020 15:33
![question](/tpl/images/cats/biologiya.png)