Physics, 02.02.2021 14:00 shamayajohnsonsh5
OCRA Industries have an unlabelled radioactive source.
One of their scientists needs to find out what radiation it is emitting
She sets up this equipment.
|
CHE
source
absorber
Look at her results.
Source in position
Absorber
Detector reading
in counis per minute
no
yes
none
2500
yes
paper
ga
yes
3 min aluminium
1795
yes
1 con lead
Answers: 3
Physics, 22.06.2019 16:00
What is the freezing point of radiator fluid that is 50% antifreeze by mass? kf for water is 1.86 ∘c/m.
Answers: 3
Physics, 22.06.2019 19:30
Which describes increasing the efficiency of energy resource
Answers: 1
Physics, 23.06.2019 06:30
If a car is traveling on the highway at a constant velocity, the force that pushes the car forward must be a. equal to the weight of the car. b. less than the force of friction exerted upon the car. c. equal to the force of friction exerted upon the car. d. greater than the weight of the car.
Answers: 1
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
OCRA Industries have an unlabelled radioactive source.
One of their scientists needs to find out wh...
Mathematics, 16.07.2019 21:30
English, 16.07.2019 21:30
Biology, 16.07.2019 21:30
Mathematics, 16.07.2019 21:30
Computers and Technology, 16.07.2019 21:30
History, 16.07.2019 21:30
Biology, 16.07.2019 21:30
Physics, 16.07.2019 21:30
History, 16.07.2019 21:30
Mathematics, 16.07.2019 21:30
Physics, 16.07.2019 21:30
Computers and Technology, 16.07.2019 21:30
Health, 16.07.2019 21:30
History, 16.07.2019 21:30
Computers and Technology, 16.07.2019 21:30
English, 16.07.2019 21:30