subject

Physics, 04.05.2021 14:00 xmanavongrove55

42v3g4f4 4 t43 t3 t43t 43t3

ansver

Answers: 1

Show answers

Another question on Physics

question

Physics, 21.06.2019 22:00

To run the physics cart, the fan speed of the cart is manipulated. this is the (blank) variable. the cart accelerates due to the speed of the fan. acceleration is therefore the (blank) variable. a “constant” is a parameter that stays the same regardless of the variables. one parameter of the cart that is held constant is the (blank) .

Answers: 1

question

Physics, 22.06.2019 01:00

What are igneous intrusions and extrusions

Answers: 2

question

Physics, 22.06.2019 04:30

Erosion of the beach is normally a slow process. however, in certain situations, large chunks of shore may wash out to sea. what could cause this to happen?

Answers: 3

question

Physics, 22.06.2019 09:00

Connie has $660,000 she wants to save. if the fdic insurance limit per depositor, per bank, is $250,000, which of these way is distributing her money between three banks will guarantee that all of her money is insured ?

Answers: 3

You know the right answer?

42v3g4f4 4 t43 t3 t43t 43t3...

Questions

question

Engineering, 11.07.2019 04:20

Ametal rod, 20 mm diameter, is tested in tension (force applied axially). the total extension over a length of 80 mm is 3.04 x 102 mm for a pull of 25...

question

Engineering, 11.07.2019 04:20

Avariable dielectric capacitive displacement sensor consists of 2 square metal plates w=6 cm separated by a gap of 1 mm. a sheet of dielectric materia...

question

Engineering, 11.07.2019 04:20

How can i determine the ultimate and yield strengths of the material prior to forming; the yield strength of the material at the corners of the secti...

question

Engineering, 11.07.2019 04:20

An air conditioner unit uses an electrical power input of 100w to drive the system and rejects 440w of heat to the kitchen air. calculate the air cond...

question

Engineering, 11.07.2019 04:20

Design a portfolio for the processing of squeezing juice from sugarcane to the production of sugar cubes and your design criteria must include all mac...

question

Engineering, 11.07.2019 04:20

Anozzle in a horizontal orientation is designed to have steady flowing steam exit it with a velocity of 250 m/s. if the outlet specific enthalpy of th...

question

Engineering, 11.07.2019 04:20

In jacobi method, new values are calculated using the newly calculated values of all unknowns. a)true b)- false...

question

Engineering, 11.07.2019 04:20

Aheat pump with refrigerant-134a as the working fluid is used to keep aspace at 25°c by absorbing heat from geothermal water that enters the evaporato...

question

Engineering, 11.07.2019 04:20

In an experiment, atmospheric air at 54°c is flowing at 30 m/s over the upper surface of a horizontal plate that is maintained at 0°c. the plate is sq...

question

Engineering, 11.07.2019 04:20

The amount of sensible heat per kg needed to increase the temperature of air from db-20°c & rh-20% to db-25°c and rh: 50% is a)18kj/kg b)25 c)31...

question

Engineering, 11.07.2019 04:20

A53-kg copper block initially at 107c is dropped into an insulated tank that contains 178l of water at 12c. determine the final equilibrium temperatur...

question

Engineering, 11.07.2019 04:20

Steam enters an adiabatic turbine at 10 mpa and 500°c and leaves at 10 kpa with a quality of 90 percent. neglecting the changes in kinetic and potenti...

question

Engineering, 11.07.2019 04:20

Given an idealephericaly radiating noise source, what would the sound level reduction be if the distance between the and receiver is decreased by a de...

question

Engineering, 11.07.2019 04:20

Develop two project life-cycle models for the construction of a (theoretical) thermal transfer plant. state assumptions....

question

Engineering, 11.07.2019 04:20

A"good" measurement system exhibits (choose one) (a)- amplitude linearity, large bandwidth, and phase linearity (b)- amplitude linearity, small bandwi...

question

Engineering, 11.07.2019 04:20

What are the differences between cooling curve of the pure metal and alloy? draw the cooling curve of each and explain each of them in 2-3 lines....

question

Engineering, 11.07.2019 04:20

The radiator of a steam heating system has a volume of 20 l and is filled with superheated water vapor at 200 kpa and 150°c. at this moment both the i...

question

Engineering, 11.07.2019 04:20

How can the solubility of gas changes in metal during solidification from the melt to the solid at room temperature? draw a plot about it and explain...

question

Engineering, 11.07.2019 04:20

Refrigerant-134a enters an adiabatic compressor as saturated vapor at 100 kpa at a rate of 0.7 m3/min and exits at 1-mpa pressure. if the isentropic e...

question

Engineering, 11.07.2019 04:20

Apiston-cylinder device contains 1.370 kg of nitrogen gas at 120 kpa and 27°c. the gas is now compressed slowly in a polytropic process during which p...

More questions: Physics Another questions

Questions on the website: 13722363